JS28F640J3D75 Micron Technology Inc, JS28F640J3D75 Datasheet - Page 33
![no-image](/images/manufacturer_photos/0/4/441/micron_technology_inc_sml.jpg)
JS28F640J3D75
Manufacturer Part Number
JS28F640J3D75
Description
Manufacturer
Micron Technology Inc
Datasheet
1.JS28F640J3D75.pdf
(68 pages)
Specifications of JS28F640J3D75
Cell Type
NOR
Density
64Mb
Access Time (max)
75ns
Interface Type
Parallel
Boot Type
Not Required
Address Bus
23/22Bit
Operating Supply Voltage (typ)
3/3.3V
Operating Temp Range
-40C to 85C
Package Type
TSOP
Program/erase Volt (typ)
2.7 to 3.6V
Sync/async
Asynchronous
Operating Temperature Classification
Industrial
Operating Supply Voltage (min)
2.7V
Operating Supply Voltage (max)
3.6V
Word Size
8/16Bit
Number Of Words
8M/4M
Mounting
Surface Mount
Pin Count
56
Lead Free Status / Rohs Status
Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
JS28F640J3D75
Manufacturer:
INTEL
Quantity:
5 530
Company:
Part Number:
JS28F640J3D75
Manufacturer:
INTEL
Quantity:
9
Part Number:
JS28F640J3D75
Manufacturer:
INTEL
Quantity:
20 000
Company:
Part Number:
JS28F640J3D75A
Manufacturer:
INTEL
Quantity:
5 530
Company:
Part Number:
JS28F640J3D75A
Manufacturer:
INTEL
Quantity:
5 530
Company:
Part Number:
JS28F640J3D75A
Manufacturer:
NUMONYX
Quantity:
3 456
Part Number:
JS28F640J3D75A
Manufacturer:
NUMONYX
Quantity:
20 000
Part Number:
JS28F640J3D75E
Manufacturer:
MUMONYS
Quantity:
20 000
Part Number:
JS28F640J3D75ES
Manufacturer:
INTEL
Quantity:
20 000
Numonyx™ Embedded Flash Memory (J3 v. D)
Note:
Table 16: Enhanced Configuration Register
Table 17: Asynchronous 8-Word Page Mode Command Bus-Cycle Definition
8.1.2
8.2
November 2007
308551-05
Set Enhanced Configuration
Register (Set ECR)
ECR
ECR[15:14]
15
Reserved
ECR[12:0]
1. X = Any valid address within the device. ECD = Enhanced Configuration Register Data
ECR[13]
BITS
ECR
Command
14
RFU
RFU
Length
For forward compatibility reasons, if the 8-word Asynchronous Page mode is used on
Numonyx™ Embedded Flash Memory (J3 v. D), a Clear Status Register command must
be executed after issuing the Set Enhanced Configuration Register command. See
Table 17
• “1” = 8 Word Page mode
• “0” = 4 Word Page mode
Output Disable
With CEx asserted, and OE# at a logic-high level (V
Output signals D[15:0] are placed in a high-impedance state.
Bus Writes
Writing or Programming to the device, is where the host writes information or data into
the flash device for non-volatile storage. When the flash device is programmed, ‘ones’
are changed to ‘zeros’. ‘Zeros’ cannot be programed back to ‘ones’. To do so, an erase
operation must be performed. Writing commands to the Command User Interface (CUI)
enables various modes of operation, including the following:
Erasing is performed on a block basis – all flash cells within a block are erased together.
Any information or data previously stored in the block will be lost. Erasing is typically
done prior to programming. The Block Erase command requires appropriate command
data and an address within the block to be erased. The Byte/Word Program command
requires the command and address of the location to be written. Set Block Lock-Bit
commands require the command and block within the device to be locked. The Clear
Block Lock-Bits command requires the command and address within the device to be
cleared.
Page
ECR
• Reading of array data
• Common Flash Interface (CFI) data
• Identifier codes, inspection, and clearing of the Status Register
• Block Erasure, Program, and Lock-bit Configuration (when V
13
ECR
for further details.
12
Required
Cycles
Bus
ECR
2
11
DESCRIPTION
ECR
10
Oper
Write
ECR
9
First Bus Cycle
ECR
Addr
8
ECD
(1)
ECR
7
Reserved
ECR
0060h
Data
6
All bits should be set to 0.
All bits should be set to 0.
IH
ECR
5
), the device outputs are disabled.
Oper
Write
ECR
4
Second Bus Cycle
ECR
PEN
3
NOTES
Addr
= V
ECD
ECR
2
(1)
PENH
ECR
)
1
Datasheet
0004h
Data
ECR
0
33