SC16C654BIB64,157 NXP Semiconductors, SC16C654BIB64,157 Datasheet - Page 10
![IC QUAD UART 64BYTE 64LQFP](/photos/6/98/69856/568-64-lqfp_sot314-2_sml.jpg)
SC16C654BIB64,157
Manufacturer Part Number
SC16C654BIB64,157
Description
IC QUAD UART 64BYTE 64LQFP
Manufacturer
NXP Semiconductors
Datasheet
1.SC16C654BIBS528.pdf
(58 pages)
Specifications of SC16C654BIB64,157
Features
False-start Bit Detection
Number Of Channels
4, QUART
Fifo's
64 Byte
Voltage - Supply
2.5V, 3.3V, 5V
With Auto Flow Control
Yes
With Irda Encoder/decoder
Yes
With False Start Bit Detection
Yes
With Modem Control
Yes
With Cmos
Yes
Mounting Type
Surface Mount
Package / Case
64-LQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
935274936157
SC16C654BIB64
SC16C654BIB64
SC16C654BIB64
SC16C654BIB64
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
SC16C654BIB64,157
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Philips Semiconductors
Table 2:
9397 750 14965
Product data sheet
Symbol
16/68
A0
A1
A2
A3
A4
CDA
CDB
CDC
CDD
CLKSEL
CS
Pin
PLCC68 LQFP64 HVQFN48 LFBGA6
31
34
33
32
20
50
9
27
43
61
30
16
Pin description
5.2 Pin description
-
24
23
22
-
-
64
18
31
49
-
-
14
17
16
15
9
31
-
-
24
-
-
5
4
-
K5
J5
K4
-
-
A1
K2
J9
A10
-
-
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 64-byte FIFOs
Rev. 02 — 20 June 2005
Type Description
I
I
I
I
I
I
I
I
16/68 Interface type select (input with internal pull-up).
This input provides the 16 (Intel) or 68 (Motorola) bus
interface type select. The functions of IOR, IOW,
INTA to INTD, and CSA to CSD are re-assigned with the
logical state of this pin. When this pin is a logic 1, the
16 mode interface (16C654) is selected. When this pin is a
logic 0, the 68 mode interface (68C654) is selected. When
this pin is a logic 0, IOW is re-assigned to R/W, RESET is
re-assigned to RESET, IOR is not used, and INTA to INTD
are connected in a wire-OR configuration. The wire-OR
outputs are connected internally to the open-drain IRQ
signal output. This pin is not available on 64-pin packages
which operate in the 16 mode only.
Address 0 select bit. Internal registers address selection in
16 and 68 modes.
Address 1 select bit. Internal registers address selection in
16 and 68 modes.
Address 2 select bit. Internal registers address selection in
16 and 68 modes.
Address 3, Address 4 select bits. When the 68 mode is
selected, these pins are used to address or select individual
UARTs (providing CS is a logic 0). In the 16 mode, these
pins are re-assigned as chip selects, see CSB and CSC.
These pins are not available on 64-pin packages which
operate in the 16 mode only.
Carrier Detect (active LOW). These inputs are associated
with individual UART channels A through D. A logic 0 on this
pin indicates that a carrier has been detected by the modem
for that channel.
Clock Select. The 1 or 4 pre-scalable clock is selected by
this pin. The 1 clock is selected when CLKSEL is a logic 1
(connected to V
logic 0 (connected to GND). MCR[7] can override the state
of this pin following reset or initialization (see MCR[7]). This
pin is not available on 64-pin packages which provide
MCR[7] selection only.
Chip Select (active LOW). In the 68 mode, this pin
functions as a multiple channel chip enable. In this case, all
four UARTs (A to D) are enabled when the CS pin is a
logic 0. An individual UART channel is selected by the data
contents of address bits A[3:4]. when the 16 mode is
selected (68-pin devices), this pin functions as CSA (see
definition under CSA, CSB). This pin is not available on
64-pin packages which operate in the 16 mode only.
SC16C654B/654DB
CC
) or the 4 is selected when CLKSEL is a
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
10 of 58