SC16C654BIB64,157 NXP Semiconductors, SC16C654BIB64,157 Datasheet - Page 20
![IC QUAD UART 64BYTE 64LQFP](/photos/6/98/69856/568-64-lqfp_sot314-2_sml.jpg)
SC16C654BIB64,157
Manufacturer Part Number
SC16C654BIB64,157
Description
IC QUAD UART 64BYTE 64LQFP
Manufacturer
NXP Semiconductors
Datasheet
1.SC16C654BIBS528.pdf
(58 pages)
Specifications of SC16C654BIB64,157
Features
False-start Bit Detection
Number Of Channels
4, QUART
Fifo's
64 Byte
Voltage - Supply
2.5V, 3.3V, 5V
With Auto Flow Control
Yes
With Irda Encoder/decoder
Yes
With False Start Bit Detection
Yes
With Modem Control
Yes
With Cmos
Yes
Mounting Type
Surface Mount
Package / Case
64-LQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
935274936157
SC16C654BIB64
SC16C654BIB64
SC16C654BIB64
SC16C654BIB64
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
SC16C654BIB64,157
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Philips Semiconductors
9397 750 14965
Product data sheet
6.9 Programmable baud rate generator
When two interrupt conditions have the same priority, it is important to service these
interrupts correctly. Receive Data Ready and Receive Time Out have the same interrupt
priority (when enabled by IER[0]). The receiver issues an interrupt after the number of
characters have reached the programmed trigger level. In this case, the
SC16C654B/654DB FIFO may hold more characters than the programmed trigger level.
Following the removal of a data byte, the user should re-check LSR[0] for additional
characters. A Receive Time Out will not occur if the receive FIFO is empty. The time-out
counter is reset at the center of each stop bit received or each time the receive holding
register (RHR) is read. The actual time-out value is 4 character time.
In the 16 mode for the PLCC68 package, the system/board designer can optionally
provide software controlled 3-state interrupt operation. This is accomplished by INTSEL
and MCR[3]. When INTSEL interface pin is left open or made a logic 0, MCR[3] controls
the 3-state interrupt outputs, INTA to INTD. When INTSEL is a logic 1, MCR[3] has no
effect on the INTA to INTD outputs, and the package operates with interrupt outputs
enabled continuously.
The SC16C654B/654DB supports high speed modem technologies that have increased
input data rates by employing data compression schemes. For example, a 33.6 kbit/s
modem that employs data compression may require a 115.2 kbit/s input data rate.
A 128.0 kbit/s ISDN modem that supports data compression may need an input data rate
of 460.8 kbit/s.
A single baud rate generator is provided for the transmitter and receiver, allowing
independent TX/RX channel control. The programmable Baud Rate Generator is capable
of accepting an input clock up to 80 MHz (for 3.3 V and 5 V operation), as required for
supporting a 5 Mbit/s data rate. The SC16C654B/654DB can be configured for internal or
external clock operation. For internal clock oscillator operation, an industry standard
microprocessor crystal (parallel resonant/22 pF to 33 pF load) is connected externally
between the XTAL1 and XTAL2 pins; see
connected to the XTAL1 pin to clock the internal baud rate generator for standard or
custom rates; see
The generator divides the input 16 clock by any divisor from 1 to (2
SC16C654B/654DB divides the basic external clock by 16. Further division of this 16
clock provides two table rates to support low and high data rate applications using the
same system design. After a hardware reset and during initialization, the
Fig 10. Crystal oscillator connection
Table
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 64-byte FIFOs
XTAL1
Rev. 02 — 20 June 2005
7.
1.8432 MHz
C1
22 pF
X1
XTAL2
C2
33 pF
Figure
10. Alternatively, an external clock can be
SC16C654B/654DB
XTAL1
1.8432 MHz
C1
22 pF
X1
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
XTAL2
002aaa870
1.5 k
C2
47 pF
16
1). The
20 of 58