SC16C654IA68,529 NXP Semiconductors, SC16C654IA68,529 Datasheet - Page 15
![IC UART QUAD W/FIFO 68-PLCC](/photos/6/98/69865/68-plcc_sot188-3_pkg_sml.jpg)
SC16C654IA68,529
Manufacturer Part Number
SC16C654IA68,529
Description
IC UART QUAD W/FIFO 68-PLCC
Manufacturer
NXP Semiconductors
Datasheet
1.SC16C654DIB64151.pdf
(52 pages)
Specifications of SC16C654IA68,529
Number Of Channels
4, QUART
Fifo's
64 Byte
Voltage - Supply
2.5V, 3.3V, 5V
With Auto Flow Control
Yes
With Irda Encoder/decoder
Yes
With False Start Bit Detection
Yes
With Modem Control
Yes
With Cmos
Yes
Mounting Type
Surface Mount
Package / Case
68-LCC (J-Lead)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
568-3282-5
935270051529
SC16C654IA68-S
935270051529
SC16C654IA68-S
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
SC16C654IA68,529
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Philips Semiconductors
9397 750 11617
Product data
6.10 Hardware/software and time-out interrupts
6.8 Special feature software flow control
6.9 Xon any feature
suspend/resume transmissions. When double 8-bit Xon/Xoff characters are selected,
the SC16C654/654D compares two consecutive receive characters with two software
flow control 8-bit values (Xon1, Xon2, Xoff1, Xoff2) and controls TX transmissions
accordingly. Under the above described flow control mechanisms, flow control
characters are not placed (stacked) in the user accessible RX data buffer or FIFO.
In the event that the receive buffer is overfilling and flow control needs to be executed,
the SC16C654/654D automatically sends an Xoff message (when enabled) via the
serial TX output to the remote modem. The SC16C654/654D sends the Xoff1,2
characters as soon as received data passes the programmed trigger level. To clear
this condition, the SC16C654/654D will transmit the programmed Xon1,2 characters
as soon as receive data drops below the programmed trigger level.
A special feature is provided to detect an 8-bit character when EFR[5] is set. When
8-bit character is detected, it will be placed on the user-accessible data stack along
with normal incoming RX data. This condition is selected in conjunction with
EFR[0-3]. Note that software flow control should be turned off when using this special
mode by setting EFR[0-3] to a logic 0.
The SC16C654/654D compares each incoming receive character with Xoff2 data. If a
match exists, the received data will be transferred to the FIFO, and ISR[4] will be set
to indicate detection of a special character. Although the Internal Register Table
(Table
number of bits is dependent on the programmed word length. Line Control Register
bits LCR[0-1] define the number of character bits, i.e., either 5 bits, 6 bits, 7 bits or
8 bits. The word length selected by LCR[0-1] also determine the number of bits that
will be used for the special character comparison. Bit 0 in the X-registers corresponds
with the LSB bit for the receive character.
A special feature is provided to return the Xoff flow control to the inactive state
following its activation. In this mode, any RX character received will return the Xoff
flow control to the inactive state so that transmissions may be resumed with a remote
buffer. This feature is more fully defined in
Three special interrupts have been added to monitor the hardware and software flow
control. The interrupts are enabled by IER[5-7]. Care must be taken when handling
these interrupts. Following a reset, the transmitter interrupt is enabled, the
SC16C654/654D will issue an interrupt to indicate that the Transmit Holding Register
is empty. This interrupt must be serviced prior to continuing operations. The LSR
register provides the current singular highest priority interrupt only. It could be noted
that CTS and RTS interrupts have lowest interrupt priority. A condition can exist
where a higher priority interrupt may mask the lower priority CTS/RTS interrupt(s).
Only after servicing the higher pending interrupt will the lower priority CTS/TRS
interrupt(s) be reflected in the status register. Servicing the interrupt without
investigating further interrupt conditions can result in data errors.
8) shows each X-Register with eight bits of character information, the actual
Quad UART with 64-byte FIFO and infrared (IrDA) encoder/decoder
Rev. 04 — 19 June 2003
Section 6.7 “Software flow
SC16C654/654D
© Koninklijke Philips Electronics N.V. 2003. All rights reserved.
control”.
15 of 52