AD711 Analog Devices, AD711 Datasheet
AD711
Specifications of AD711
Available stocks
Related parts for AD711
AD711 Summary of contents
Page 1
... The superior ac and dc performance of this op amp makes it suitable for active filter applications. With a slew rate of 16 V/ms and a settling time ± 0.01%, the AD711 is ideal as a buffer for 12-bit D/A and A/D Converters and as a high-speed integrator. The settling time is unmatched by any similar IC amplifier ...
Page 2
... AD711–SPECIFICATIONS Parameter Min 1 INPUT OFFSET VOLTAGE Initial Offset MIN MAX vs. Temp vs. Supply 76/76/76 MIN MAX Long-Term Stability 2 INPUT BIAS CURRENT MAX = ± INPUT OFFSET CURRENT MAX FREQUENCY RESPONSE Small Signal Bandwidth 3 ...
Page 3
... Differential Input Voltage . . . . . . . . . . . . . . . . . . +V Storage Temperature Range ( –65∞C to +150∞C Storage Temperature Range ( –65∞C to +125∞C Operating Temperature Range AD711J 0∞C to +70∞C AD711A/B –40∞C to +85∞C AD711S –55∞C to +125∞C Lead Temperature Range (Soldering 60 sec 300∞C ...
Page 4
... AD711–Typical Performance Characteristics SUPPLY VOLTAGE – Volts TPC 1. Input Voltage Swing vs. Supply Voltage 2.75 2.50 2.25 2.00 1. SUPPLY VOLTAGE – Volts TPC 4. Quiescent Current vs. Sup- ply Voltage 100 V = 15V MAX J GRADE LIMIT 25 0 –10 – ...
Page 5
... INPUT FREQUENCY – Hz TPC 14. Large Signal Frequency Response 1k 100 100 1k 10k 100k FREQUENCY – Hz TPC 17. Input Noise Voltage Spectral Density –5– AD711 110 100 +SUPPLY 80 –SUPPLY SUPPLIES S 20 WITH 1V p-p SINE WAVE 100 1k ...
Page 6
... TPC 22b. Unity Gain Follower Pulse Response (Large Signal) TPC 23b. Unity Gain Inverter Pulse Response (Large Signal) –6– 0.1 F 0.1 F 1.3Mk 10k AD711 AD711 0.1 F 0.1 F 10k –V – TPC 21. Offset Null Configurations TPC 22c. Unity Gain Follower Pulse Response (Small Signal) TPC 23c ...
Page 7
... DACs; therefore, the amplifier settling time has been the major limitation to a high-speed voltage-output D-to-A function. The introduction of the AD711/712 family of op amps with their 1 ms (to ± 0.01% of final value) settling time now permits the full high-speed capabilities of most modern DACs to be realized. ...
Page 8
... Since the value of C ˜ (3) accuracy, Equation 2 can be used to choose a small capacitor, ¯ cancel the input pole and optimize amplifier response. F Figure graphical solution of Equation 2 for the AD711 with kW (3) 30 ...
Page 9
... Upper Trace: Output of AD711 Under Test (5 V/Div) Lower Trace: Amplified Error Voltage (0.01%/Div) GUARDING The low input bias current (15 pA) and low noise characteristics of the AD711 BiFET op amp make it suitable for electrometer applications such as photo diode preamplifiers and picoampere DATA DYNAMICS ...
Page 10
... The AD711C grade is specified at a maximum level of 4 bandwidth. Each AD711C receives a 100% noise test for two 10-second intervals; devices with any excursion in excess of 4 ...
Page 11
... The amplifier’s bandwidth in conjunction with the filter’s gain will dictate the frequency response of the filter. The use of a high performance amplifier such a s the AD711 will minimize both dc and ac errors in all active filter applica- tions. ...
Page 12
... AD711 9-POLE CHEBYCHEV FILTER Figure 17 shows the AD711 and its dual counterpart, the AD712 9-pole Chebychev filter using active frequency dependent negative resistors (FDNR). With a cutoff frequency of 50 kHz and better than 90 dB rejection, it may be used as an anti-aliasing filter for a 12-bit data acquisition system with 100 kHz throughput. ...
Page 13
... MAX 0.41 (0.0160) 0.0400 (1.02) 0.0100 (0.25) COMPLIANT TO JEDEC STANDARDS MO-002AK CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETERS DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN –13– AD711 (Q-8) 0.055 (1.40) MAX 8 5 0.310 (7.87) 0.220 (5.59 0.100 (2.54) BSC ...
Page 14
... AD711 Revision History Location 10/02—Data Sheet changed from REV REV. E. Edits to ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 10/02—Data Sheet changed from REV REV. D. Edits to CONNECTION DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Updated OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5/02—Data Sheet changed from REV REV. C. Change from Small Outline Package (R- Edits to ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Deleted METALLIZATION PHOTOGRAPH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 – ...
Page 15
–15– ...
Page 16
–16– ...