AT90CAN64 Atmel Corporation, AT90CAN64 Datasheet - Page 63

• Manufacturer Part Number: AT90CAN64
• Manufacturer: Atmel Corporation

Specifications of AT90CAN64

• Flash (kbytes): 64 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 53
• Ext Interrupts: 8
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Uart: 2
• Can: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 4
• Eeprom (bytes): 2048
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 8
• Input Capture Channels: 2
• Pwm Channels: 7
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

7679H–CAN–08/08
When the BOOTRST Fuse is programmed and the Boot section size set to 8K bytes, the most
typical and general program setup for the Reset and Interrupt Vector Addresses is:
When the BOOTRST Fuse is programmed, the Boot section size set to 8K bytes and the IVSEL
bit in the MCUCR Register is set before any interrupts are enabled, the most typical and general
program setup for the Reset and Interrupt Vector Addresses is:
0x0004
0x0005
;
.org (BootResetAdd + 0x0002)
0x..02
0x..04
...
0x..0C
;Address Labels
.org 0x0002
0x0002
0x0004
...
0x002C
;
.org (BootResetAdd)
0x..00
0x..01
0x..02
0x..03
0x..04
0x..05
;Address Labels
;
.org (BootResetAdd)
0x..00
0x0002
0x..04
...
0x..44
;
0x..46
0x..47
0x..48
0x..49
0x..4A
0x..4B
RESET: ldi
RESET: ldi
sei
<instr>
jmp
jmp
...
jmp
jmp
jmp
...
jmp
out
ldi
out
sei
<instr>
jmp
jmp
jmp
...
jmp
out
ldi
out
sei
<instr>
EXT_INT0
PCINT0
...
SPM_RDY
Code
EXT_INT0
PCINT0
...
SPM_RDY
r16,high(RAMEND) ; Main program start
SPH,r16
r16,low(RAMEND)
SPL,r16
Code
RESET
EXT_INT0
PCINT0
...
SPM_RDY
r16,high(RAMEND) ; Main program start
SPH,r16
r16,low(RAMEND)
SPL,r16
xxx
xxx
xxx
; Enable interrupts
; IRQ0 Handler
; PCINT0 Handler
;
; Store Program Memory Ready Handler
; IRQ0 Handler
; PCINT0 Handler
;
; Store Program Memory Ready Handler
; Set Stack Pointer to top of RAM
; Enable interrupts
; Reset handler
; IRQ0 Handler
; PCINT0 Handler
;
; Store Program Memory Ready Handler
; Set Stack Pointer to top of RAM
; Enable interrupts
Comments
Comments
AT90CAN32/64/128
63