AT90PWM3B Atmel Corporation, AT90PWM3B Datasheet - Page 247

• Manufacturer Part Number: AT90PWM3B
• Manufacturer: Atmel Corporation

Specifications of AT90PWM3B

• Flash (kbytes): 8 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 8
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 27
• Ext Interrupts: 4
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 125
• Analog Comparators: 3
• Resistive Touch Screen: No
• Dac Channels: 1
• Dac Resolution (bits): 10
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 105
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 5
• Output Compare Channels: 16
• Input Capture Channels: 1
• Pwm Channels: 12
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

21.8.2
4317J–AVR–08/10
ADC Control and Status Register A – ADCSRA
• Bit 3, 2, 1, 0 – MUX3, MUX2, MUX1, MUX0: ADC Channel Selection Bits
These 4 bits determine which analog inputs are connected to the ADC input. The different set-
ting are shown in
Table 21-4.
If these bits are changed during a conversion, the change will not take effect until this conversion
is complete (it means while the ADIF bit in ADCSRA register is set).
Bit
Read/Write
Initial Value
• Bit 7 – ADEN: ADC Enable Bit
Set this bit to enable the ADC.
Clear this bit to disable the ADC.
Clearing this bit while a conversion is running will take effect at the end of the conversion.
• Bit 6– ADSC: ADC Start Conversion Bit
Set this bit to start a conversion in single conversion mode or to start the first conversion in free
running mode.
Cleared by hardware when the conversion is complete. Writing this bit to zero has no effect.
The first conversion performs the initialization of the ADC.
• Bit 5 – ADATE: ADC Auto trigger Enable Bit
Set this bit to enable the auto triggering mode of the ADC.
Clear it to return in single conversion mode.
MUX3
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
ADC Input Channel Selection
MUX2
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
ADEN
R/W
7
0
Table
21-4.
ADSC
R/W
6
0
MUX1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
ADATE
R/W
5
0
ADIF
R
MUX0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
4
0
ADIE
R/W
3
0
AT90PWM2/3/2B/3B
Description
ADC0
ADC1
ADC2
ADC3
ADC4
ADC5
ADC6
ADC7
ADC8
ADC9
ADC10
AMP0
AMP1 (- is ADC8, + is ADC9)
Reserved
Bandgap
GND
ADPS2
R/W
2
0
ADPS1
R/W
1
0
ADPS0
R/W
0
0
ADCSRA
247