ATmega16M1 Automotive Atmel Corporation, ATmega16M1 Automotive Datasheet - Page 118

• Manufacturer Part Number: ATmega16M1 Automotive
• Manufacturer: Atmel Corporation

Specifications of ATmega16M1 Automotive

• Flash (kbytes): 16 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 12
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 27
• Ext Interrupts: 27
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Uart: 1
• Can: 1
• Lin: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 125
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 1
• Dac Resolution (bits): 10
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 150
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 14
• Input Capture Channels: 1
• Pwm Channels: 10
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

14.11.7
14.11.8
118
Atmel ATtiny24/44/84 [Preliminary]
ICR1H and ICR1L – Input Capture Register 1
TIMSK1 – Timer/Counter Interrupt Mask Register 1
The Input Capture is updated with the counter (TCNT1) value each time an event occurs on
the ICP1 pin (or optionally on the Analog Comparator output for Timer/Counter1). The Input
Capture can be used for defining the counter TOP value.
The input capture register is 16 bits in size. To ensure that both the high and low bytes are
read simultaneously when the CPU accesses these registers, the access is performed using
an 8-bit temporary high byte register (TEMP). This temporary register is shared by all the other
16-bit registers.
• Bit 7,6,4,3 – Reserved Bit
This bit is reserved for future use. For ensuring compatibility with future devices, this bit must
be written to logical zero when the register is written.
• Bit 5 – ICIE1: Timer/Counter1, Input Capture Interrupt Enable
When this bit is written to logical one and the I-flag in the status register is set (interrupts glob-
ally enabled), the timer/counter 1 input capture interrupt is enabled. The corresponding inter-
rupt vector (see
ICF1 Flag, located in TIFR1, is set.
• Bit 2– OCIE1B: Timer/Counter1, Output Compare B Match Interrupt Enable
When this bit is written to logical one and the I-flag in the status register is set (interrupts glob-
ally enabled), the timer/counter 1 output compare B match interrupt is enabled. The
corresponding interrupt vector (see
located in TIFR1, is set.
• Bit 1– OCIE1A: Timer/Counter1, Output Compare A Match Interrupt Enable
When this bit is written to logical one and the I-flag in the status register is set (interrupts glob-
ally enabled), the timer/counter 1 output compare A match interrupt is enabled. The
corresponding interrupt vector (see
located in TIFR1, is set.
• Bit 0 – TOIE1: Timer/Counter1, Overflow Interrupt Enable
When this bit is written to logical one and the I-flag in the status register is set (interrupts glob-
ally enabled), the timer/counter 1 overflow interrupt is enabled. The corresponding interrupt
vector (see
Bit
0x25 (0x45)
0x24 (0x44)
Read/Write
Initial Value
Bit
0x0C (0x2C)
Read/Write
Initial Value
“Interrupts” on page
R/W
“Accessing 16-bit Registers” on page
“Interrupts” on page
R
7
0
7
–
0
R/W
R
6
0
6
–
0
50) is executed when the TOV1 flag, located in TIFR1, is set.
ICIE1
R/W
R/W
5
0
5
0
“Interrupts” on page
“Interrupts” on page
50) is executed when the
R/W
4
0
R
4
–
0
ICR1[15:8]
ICR1[7:0]
R/W
3
0
R
3
–
0
94.
50) is executed when the OCF1B flag,
50) is executed when the OCF1A flag,
OCIE1B
R/W
R/W
2
0
2
0
OCIE1A
R/W
R/W
1
0
1
0
R/W
TOIE1
R/W
0
0
0
0
7701E–AVR–02/11
ICR1H
TIMSK1
ICR1L