ATmega32U4 Atmel Corporation, ATmega32U4 Datasheet - Page 79

• Manufacturer Part Number: ATmega32U4
• Manufacturer: Atmel Corporation

Specifications of ATmega32U4

• Flash (kbytes): 32 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 14
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 26
• Ext Interrupts: 13
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 12
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 3.3
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 12
• Input Capture Channels: 2
• Pwm Channels: 8
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

7766F–AVR–11/10
Table 10-9.
Table 10-10. Overriding Signals for Alternate Functions in PD3.PD0
Note:
Signal Name
PUOE
PUOV
DDOE
DDOV
PVOE
PVOV
DIEOE
DIEOV
DI
AIO
Signal Name
PUOE
PUOV
DDOE
DDOV
PVOE
PVOV
DIEOE
DIEOV
DI
AIO
1. When enabled, the 2-wire Serial Interface enables Slew-Rate controls on the output pins PD0
and PD1. This is not shown in this table. In addition, spike filters are connected between the
AIO outputs shown in the port figure and the digital logic of the TWI module.
Overriding Signals for Alternate Functions PD7..PD4
PD3/INT3/TXD1
TXEN1
0
TXEN1
1
TXEN1
TXD1
INT3 ENABLE
1
INT3 INPUT
–
PD7/T0/
OC4D/ADC10
0
0
0
0
0
0
0
0
T0 INPUT
–
PD6/T1/
OC4D/ADC9
0
0
0
0
0
0
0
0
T1 INPUT
–
PD2/INT2/RXD1
RXEN1
PORTD2 • PUD
RXEN1
0
0
0
INT2 ENABLE
1
INT2 INPUT/RXD1
–
PD5/XCK1/CTS
0
0
XCK1 OUTPUT
ENABLE
1
XCK1 OUTPUT
ENABLE
XCK1 OUTPUT
0
0
XCK1 INPUT
–
PD1/INT1/SDA
TWEN
PORTD1 • PUD
TWEN
SDA_OUT
TWEN ENABLE
0
INT1 ENABLE
1
INT1 INPUT
SDA INPUT
ATmega16/32U4
(1)
PD4/ICP1/
ADC8
0
0
0
0
0
0
0
0
ICP1 INPUT
–
PD0/INT0/SCL/
OC0B
TWEN
PORTD0 • PUD
TWEN
SCL_OUT
TWEN | OC0B
ENABLE
OC0B
INT0 ENABLE
1
INT0 INPUT
SCL INPUT
79