ATmega88 Atmel Corporation, ATmega88 Datasheet - Page 266

• Manufacturer Part Number: ATmega88
• Manufacturer: Atmel Corporation

Specifications of ATmega88

• Flash (kbytes): 8 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 12
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 23
• Ext Interrupts: 24
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 6
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

2545T–AVR–05/11
Wrloop:
Rdloop:
Return:
Do_spm:
Wait_spm:
rcallDo_spm
; transfer data from RAM to Flash page buffer
ldi
ldi
ld
ld
ldi
rcallDo_spm
adiw ZH:ZL, 2
sbiw loophi:looplo, 2
brne Wrloop
; execute Page Write
subi ZL, low(PAGESIZEB)
sbci ZH, high(PAGESIZEB)
ldi
rcallDo_spm
; re-enable the RWW section
ldi
rcallDo_spm
; read back and check, optional
ldi
ldi
subi YL, low(PAGESIZEB)
sbci YH, high(PAGESIZEB)
lpm
ld
cpse r0, r1
rjmp Error
sbiw loophi:looplo, 1
brne Rdloop
; return to RWW section
; verify that RWW section is safe to read
in
sbrs temp1, RWWSB
ret
; re-enable the RWW section
ldi
rcallDo_spm
rjmp Return
; check for previous SPM complete
in
sbrc temp1, SELFPRGEN
rjmp Wait_spm
; input: spmcrval determines SPM action
; disable interrupts if enabled, store status
in
cli
; check that no EEPROM write access is present
looplo, low(PAGESIZEB)
loophi, high(PAGESIZEB)
r0, Y+
r1, Y+
spmcrval, (1<<SELFPRGEN)
spmcrval, (1<<PGWRT) | (1<<SELFPRGEN)
spmcrval, (1<<RWWSRE) | (1<<SELFPRGEN)
looplo, low(PAGESIZEB)
loophi, high(PAGESIZEB)
r0, Z+
r1, Y+
temp1, SPMCSR
spmcrval, (1<<RWWSRE) | (1<<SELFPRGEN)
temp1, SPMCSR
temp2, SREG
; If RWWSB is set, the RWW section is not ready yet
;init loop variable
;not required for PAGESIZEB<=256
;use subi for PAGESIZEB<=256
;restore pointer
;not required for PAGESIZEB<=256
;init loop variable
;not required for PAGESIZEB<=256
;restore pointer
;use subi for PAGESIZEB<=256
ATmega48/88/168
266