ATmega88 Atmel Corporation, ATmega88 Datasheet - Page 42
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
ATmega88
Manufacturer Part Number
ATmega88
Description
Manufacturer
Atmel Corporation
Specifications of ATmega88
Flash (kbytes)
8 Kbytes
Pin Count
32
Max. Operating Frequency
20 MHz
Cpu
8-bit AVR
# Of Touch Channels
12
Hardware Qtouch Acquisition
No
Max I/o Pins
23
Ext Interrupts
24
Usb Speed
No
Usb Interface
No
Spi
2
Twi (i2c)
1
Uart
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
1
Eeprom (bytes)
512
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8 to 5.5
Operating Voltage (vcc)
1.8 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
3
Output Compare Channels
6
Input Capture Channels
1
Pwm Channels
6
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATmega88-15AT
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
ATmega88-15AT1
Manufacturer:
ATMEL
Quantity:
1 000
Part Number:
ATmega88-15AT1
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
ATmega88-15ATI
Manufacturer:
ATMEL
Quantity:
5 510
Company:
Part Number:
ATmega88-15ATI
Manufacturer:
LT
Quantity:
5 510
Company:
Part Number:
ATmega88-15AZ
Manufacturer:
ATMEL
Quantity:
2 000
Company:
Part Number:
ATmega88-15AZ
Manufacturer:
ATMEL
Quantity:
120
Part Number:
ATmega88-15AZ
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATmega88-20AU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
10.8.3
10.8.4
10.8.5
10.8.6
10.8.7
2545T–AVR–05/11
Brown-out detector
Internal voltage reference
Watchdog timer
Port pins
On-chip debug system
If the brown-out detector is not needed by the application, this module should be turned off. If the
brown-out detector is enabled by the BODLEVEL Fuses, it will be enabled in all sleep modes,
and hence, always consume power. In the deeper sleep modes, this will contribute significantly
to the total current consumption. Refer to
configure the brown-out detector.
The internal voltage reference will be enabled when needed by the brown-out detection, the
analog comparator or the ADC. If these modules are disabled as described in the sections
above, the internal voltage reference will be disabled and it will not be consuming power. When
turned on again, the user must allow the reference to start up before the output is used. If the
reference is kept on in sleep mode, the output can be used immediately. Refer to
age reference” on page 48
If the watchdog timer is not needed in the application, the module should be turned off. If the
watchdog timer is enabled, it will be enabled in all sleep modes and hence always consume
power. In the deeper sleep modes, this will contribute significantly to the total current consump-
tion. Refer to
When entering a sleep mode, all port pins should be configured to use minimum power. The
most important is then to ensure that no pins drive resistive loads. In sleep modes where both
the I/O clock (clk
be disabled. This ensures that no power is consumed by the input logic when not needed. In
some cases, the input logic is needed for detecting wake-up conditions, and it will then be
enabled. Refer to the section
which pins are enabled. If the input buffer is enabled and the input signal is left floating or have
an analog signal level close to V
For analog input pins, the digital input buffer should be disabled at all times. An analog signal
level close to V
input buffers can be disabled by writing to the digital input disable registers (DIDR1 and DIDR0).
Refer to
able Register 0” on page 259
If the on-chip debug system is enabled by the DWEN Fuse and the chip enters sleep mode, the
main clock source is enabled and hence always consumes power. In the deeper sleep modes,
this will contribute significantly to the total current consumption.
“DIDR1 – Digital input disable register 1” on page 243
“Watchdog timer” on page 49
CC
I/O
/2 on an input pin can cause significant current even in active mode. Digital
) and the ADC clock (clk
for details on the start-up time.
for details.
“Digital input enable and sleep modes” on page 75
CC
/2, the input buffer will use excessive power.
“Brown-out detection” on page 47
for details on how to configure the watchdog timer.
ADC
) are stopped, the input buffers of the device will
ATmega48/88/168
and
“DIDR0 – Digital Input Dis-
for details on how to
“Internal volt-
for details on
42