ATmega8HVA Atmel Corporation, ATmega8HVA Datasheet - Page 178

• Manufacturer Part Number: ATmega8HVA
• Manufacturer: Atmel Corporation

Specifications of ATmega8HVA

• Flash (kbytes): 8 Kbytes
• Pin Count: 28
• Max. Operating Frequency: 4 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 3
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 6
• Ext Interrupts: 3
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 6
• Adc Resolution (bits): 12
• Adc Speed (ksps): 1.9
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 256
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -20 to 85
• I/o Supply Class: 1.8 to 9.0
• Operating Voltage (vcc): 1.8 to 9.0
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 4
• Input Capture Channels: 2
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

Notes:
178
0x0D (0x2D)
0x0C (0x2C)
0x1B (0x3B)
0x1A (0x3A)
0x0E (0x2E)
0x0B (0x2B)
0x0A (0x2A)
Address
0x19 (0x39)
0x18 (0x38)
0x17 (0x37)
0x16 (0x36)
0x15 (0x35)
0x14 (0x34)
0x13 (0x33)
0x12 (0x32)
0x11 (0x31)
0x10 (0x30)
0x0F (0x2F)
0x09 (0x29)
0x08 (0x28)
0x07 (0x27)
0x06 (0x26)
0x05 (0x25)
0x04 (0x24)
0x03 (0x23)
0x02 (0x22)
0x01 (0x21)
0x00 (0x20)
1. For compatibility with future devices, reserved bits should be written to zero if accessed. Reserved I/O memory addresses
2. I/O registers within the address range $00 - $1F are directly bit-accessible using the SBI and CBI instructions. In these reg-
3. Some of the status flags are cleared by writing a logical one to them. Note that the CBI and SBI instructions will operate on
4. When using the I/O specific commands IN and OUT, the I/O addresses $00 - $3F must be used. When addressing I/O regis-
ATmega8HVA/16HVA
should never be written.
isters, the value of single bits can be checked by using the SBIS and SBIC instructions.
all bits in the I/O register, writing a one back into any flag read as set, thus clearing the flag. The CBI and SBI instructions
work with registers 0x00 to 0x1F only.
ters as data space using LD and ST instructions, $20 must be added to these addresses. The ATmega8HVA/16HVA is a
complex microcontroller with more peripheral units than can be supported within the 64 location reserved in Opcode for the
IN and OUT instructions. For the Extended I/O space from $60 - $FF in SRAM, only the ST/STS/STD and LD/LDS/LDD
instructions can be used.
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
OSICSR
Name
PORTC
PORTB
PORTA
DDRB
DDRA
TIFR1
TIFR0
PINC
PINB
PINA
Bit 7
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Bit 6
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Bit 5
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
OSISEL0
Bit 4
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
PORTB3
Bit 3
PINB3
DDB3
ICF1
ICF0
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
PORTB2
OCF1B
OCF0B
Bit 2
PINB2
DDB2
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
PORTB1
PORTA1
OCF1A
OCF0A
OSIST
Bit 1
PINB1
PINA1
DDB1
DDA1
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
PORTC0
PORTB0
PORTA0
OSIEN
Bit 0
PINC0
PINB0
PINA0
TOV1
TOV0
DDB0
DDA0
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
8024A–AVR–04/08
Page
32
93
93
62
62
73
73
73
73
73
73