ATxmega64A1 Atmel Corporation, ATxmega64A1 Datasheet - Page 145

• Manufacturer Part Number: ATxmega64A1
• Manufacturer: Atmel Corporation

Specifications of ATxmega64A1

• Flash (kbytes): 64 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 32 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 78
• Ext Interrupts: 78
• Usb Speed: No
• Usb Interface: No
• Spi: 12
• Twi (i2c): 4
• Uart: 8
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 4
• Dac Resolution (bits): 12
• Temp. Sensor: Yes
• Crypto Engine: AES/DES
• Sram (kbytes): 4
• Eeprom (bytes): 2048
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.6 to 3.6
• Operating Voltage (vcc): 1.6 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 8
• Output Compare Channels: 24
• Input Capture Channels: 24
• Pwm Channels: 24
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

13.15.4
8077H–AVR–12/09
CLKEVOUT - Clock and Event Out Register
Table 13-6.
• Bit 7:6 - Reserved
These bits are reserved and will always be read as one. For compatibility with future devices,
always write these bits to zero when this register is written.
• Bit 5:4 - EVOUT[1:0] - Event Output Port
These bits decide which port the Event Channel 0 from the Event System should be output to.
Pin 7 on the selected port is always used, and the CLKOUT bits must be set different from
EVOUT. The pin must be configured as an output pin for the Signaling Event to be available on
the pin.
Table 13-7 on page 145
Table 13-7.
• Bits 3:2 - Reserved
These bits are reserved and will always be read as one. For compatibility with future devices,
always write these bits to zero when this register is written.
• Bit 1:0 - CLKOUT[1:0] - Clock Output Port
These bits decide which port the Peripheral Clock should be output to. Pin 7 on the selected port
is always used. The Clock output setting, will override the Event output setting, thus if both are
enabled on the same port pin, the Peripheral Clock will be visible. The pin must be configured as
an output pin for the Clock to be available on the pin.
Table 13-8 on page 146
Bit
+0x04
Read/Write
Initial Value
EVOUT[1:0]
00
01
10
11
VPnMAP[3:0]
1101
1110
1111
R
7
0
-
Virtual Port mapping. (Continued)
Event Channel 0 output configurations
Group Configuration
PORTP
PORTQ
PORTR
6
R
0
-
shows the possible configurations.
shows the possible configurations.
Group Configuration
OFF
PC7
PD7
PE7
R/W
5
0
EVOUT[1:0]
R/W
4
0
Description
Event out disabled
Event Channel 0 output on Port C pin 7
Event Channel 0 output on Port D pin 7
Event Channel 0 output on Port E pin 7
3
R
0
-
Description
PORTP mapped to virtual Port n
PORTQ mapped to virtual Port n
PORTR mapped to virtual Port n
R
2
0
-
R/W
1
0
CLKOUT[1:0]
XMEGA A
R/W
0
0
CLKEVOUT
145