ATxmega64B1 Atmel Corporation, ATxmega64B1 Datasheet - Page 32
ATxmega64B1
Manufacturer Part Number
ATxmega64B1
Description
Manufacturer
Atmel Corporation
Specifications of ATxmega64B1
Flash (kbytes)
64 Kbytes
Pin Count
100
Max. Operating Frequency
32 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
53
Ext Interrupts
53
Usb Transceiver
1
Usb Speed
Full Speed
Usb Interface
Device
Spi
3
Twi (i2c)
1
Uart
2
Segment Lcd
160
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
16
Adc Resolution (bits)
12
Adc Speed (ksps)
2000
Analog Comparators
4
Resistive Touch Screen
No
Temp. Sensor
Yes
Crypto Engine
AES/DES
Sram (kbytes)
8
Eeprom (bytes)
2048
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
Yes
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.6 to 3.6
Operating Voltage (vcc)
1.6 to 3.6
Fpu
No
Mpu / Mmu
no / no
Timers
3
Output Compare Channels
10
Input Capture Channels
10
Pwm Channels
10
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ATxmega64B1-AUR
Manufacturer:
ATMEL
Quantity:
210
- Current page: 32 of 425
- Download datasheet (7Mb)
4.15.5
8291A–AVR–10/11
FUSEBYTE5 – Fuse Byte 5
devices with JTAG interface. A reset is required before this bit will be read correctly after it is
changed.
Table 4-6.
• Bit 7:6 – Reserved
These bits are reserved. For compatibility with future devices, always write these bits to one
when this register is written.
• Bit 5:4 – BODACT[1:0]: BOD Operation in Active Mode
These fuse bits set the BOD operation mode when the device is in active and idle mode. For
details on the BOD and BOD operation modes refer to
Table 4-7.
• Bit 3 – EESAVE: EEPROM is Preserved through the Chip Erase
A chip erase command will normally erase the flash, EEPROM and internal SRAM. If this fuse is
programmed, the EEPROM is not erased during chip erase. This is useful if EEPROM is used to
store data independent of software revision.
Table 4-8.
Changes to the EESAVE fuse bit take effect immediately after the write timeout elapses. Hence,
it is possible to update EESAVE and perform a chip erase according to the new setting of
EESAVE without leaving and reentering programming mode.
Bit
+0x05
Read/Write
Initial Value
BODACT[1:0]
EESAVE
JTAGEN
00
01
10
11
0
1
0
1
JTAG Enable
BOD operation modes in active and idle modes.
EEPROM preserved through chip erase
R/W
7
–
1
Description
Reserved
BOD enabled in sampled mode
BOD enabled continuously
BOD disabled
Description
EEPROM is preserved during chip erase
EEPROM is erased during chip erase
Description
JTAG enabled
JTAG disabled
R/W
6
–
1
R
5
BODACT[1:0]
–
4
R
–
EESAVE
R/W
3
–
Atmel AVR XMEGA B
”Brownout Detection” on page
R/W
2
–
BODLEVEL[2:0]
R/W
1
–
R/W
0
–
107.
FUSEBYTE5
32
Related parts for ATxmega64B1
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: