M55800A Atmel Corporation, M55800A Datasheet - Page 104

• Manufacturer Part Number: M55800A
• Manufacturer: Atmel Corporation

Specifications of M55800A

• Flash (kbytes): 0 Kbytes
• Pin Count: 176
• Max. Operating Frequency: 33 MHz
• Cpu: ARM7TDMI
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 58
• Ext Interrupts: 58
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Uart: 3
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 72
• Resistive Touch Screen: No
• Dac Channels: 1
• Dac Resolution (bits): 10
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 8
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.3/5.0
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

Break
Transmit Break
104
AT91X40 Series
A break condition is a low signal level which has a duration of at least one character
(including start/stop bits and parity).
The transmitter generates a break condition on the TXD line when STTBRK is set in
US_CR (Control Register). In this case, the character present in the Transmit Shift Reg-
ister is completed before the line is held low.
To cancel a break condition on the TXD line, the STPBRK command in US_CR must be
set. The USART completes a minimum break duration of one character length. The TXD
line then returns to high level (idle state) for at least 12 bit periods to ensure that the end
of break is correctly detected. Then the transmitter resumes normal operation.
The BREAK is managed like a character:
•
•
•
In order to avoid unpredictable states:
•
•
•
•
•
•
The standard break transmission sequence is:
1. Wait for the transmitter ready
2. Send the STTBRK command
3. Wait for the transmitter ready
4. Send the STPBRK command
The next byte can then be sent:
5. Wait for the transmitter ready
6. Send the next byte
The STTBRK and the STPBRK commands are performed only if the transmitter is
ready (bit TXRDY = 1 in US_CSR)
The STTBRK command blocks the transmitter holding register (bit TXRDY is
cleared in US_CSR) until the break has started
A break is started when the Shift Register is empty (any previous character is fully
transmitted). TXEMPTY is cleared in US_CSR. The break blocks the transmitter
shift register until it is completed (high level for at least 12-bit periods after the
STPBRK command is requested)
STTBRK and STPBRK commands must not be requested at the same time
Once an STTBRK command is requested, further STTBRK commands are ignored
until the BREAK is ended (high level for at least 12-bit periods)
All STPBRK commands requested without a previous STTBRK command are
ignored
A byte written into the Transmit Holding Register while a break is pending but not
started (US_CSR.TXRDY = 0) is ignored
It is not permitted to write new data in the Transmit Holding Register while a break is
in progress (STPBRK has not been requested), even though TXRDY = 1 in
US_CSR.
A new STTBRK command must not be issued until an existing break has ended
(TXEMPTY = 1 in US_CSR)
(US_CSR.TXRDY = 1)
(write 0x0200 to US_CR)
(TXRDY = 1 in US_CSR)
(write 0x0400 to US_CR)
(TXRDY = 1 in US_CSR)
(write byte to US_THR)
1354D–ATARM–08/02