M55800A Atmel Corporation, M55800A Datasheet - Page 115

• Manufacturer Part Number: M55800A
• Manufacturer: Atmel Corporation

Specifications of M55800A

• Flash (kbytes): 0 Kbytes
• Pin Count: 176
• Max. Operating Frequency: 33 MHz
• Cpu: ARM7TDMI
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 58
• Ext Interrupts: 58
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Uart: 3
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 72
• Resistive Touch Screen: No
• Dac Channels: 1
• Dac Resolution (bits): 10
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 8
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.3/5.0
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

USART Channel Status Register
Name:
Access Type:Read Only
Reset Value: 0x18
Offset:
• RXRDY: Receiver Ready (Code Label US_RXRDY)
0 = No complete character has been received since the last read of the US_RHR or the receiver is disabled.
1 = At least one complete character has been received and the US_RHR has not yet been read.
• TXRDY: Transmitter Ready (Code Label US_TXRDY)
0 = US_THR contains a character waiting to be transferred to the Transmit Shift Register, or an STTBRK command has
been requested.
1 = US_THR is empty and there is no Break request pending TSR availability.
Equal to zero when the USART is disabled or at reset. Transmitter Enable command (in US_CR) sets this bit to one.
• RXBRK: Break Received/End of Break (Code Label US_RXBRK)
0 = No Break Received nor End of Break has been detected since the last “Reset Status Bits” command in the Control
Register.
1 = Break Received or End of Break has been detected since the last “Reset Status Bits” command in the Control Register.
• ENDRX: End of Receiver Transfer (Code Label US_ENDRX)
0 = The End of Transfer signal from the Peripheral Data Controller channel dedicated to the receiver is inactive.
1 = The End of Transfer signal from the Peripheral Data Controller channel dedicated to the receiver is active.
• ENDTX: End of Transmitter Transfer (Code Label US_ENDTX)
0 = The End of Transfer signal from the Peripheral Data Controller channel dedicated to the transmitter is inactive.
1 = The End of Transfer signal from the Peripheral Data Controller channel dedicated to the transmitter is active.
• OVRE: Overrun Error (Code Label US_OVRE)
0 = No byte has been transferred from the Receive Shift Register to the US_RHR when RxRDY was asserted since the last
“Reset Status Bits” command.
1 = At least one byte has been transferred from the Receive Shift Register to the US_RHR when RxRDY was asserted
since the last “Reset Status Bits” command.
• FRAME: Framing Error (Code Label US_FRAME)
0 = No stop bit has been detected low since the last “Reset Status Bits” command.
1 = At least one stop bit has been detected low since the last “Reset Status Bits” command.
1354D–ATARM–08/02
PARE
31
23
15
–
–
–
7
US_CSR
0x14
FRAME
30
22
14
–
–
–
6
OVRE
29
21
13
–
–
–
5
ENDTX
28
20
12
–
–
–
4
ENDRX
27
19
11
–
–
–
3
RXBRK
26
18
10
–
–
–
2
AT91X40 Series
TXEMPTY
TXRDY
25
17
–
–
9
1
TIMEOUT
RXRDY
24
16
–
–
8
0
115