SAM9G46 Atmel Corporation, SAM9G46 Datasheet - Page 24

• Manufacturer Part Number: SAM9G46
• Manufacturer: Atmel Corporation

Specifications of SAM9G46

• Flash (kbytes): 0 Kbytes
• Pin Count: 324
• Max. Operating Frequency: 400 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 160
• Ext Interrupts: 160
• Usb Transceiver: 3
• Usb Speed: Hi-Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 2
• Uart: 5
• Lin: 4
• Ssc: 2
• Ethernet: 1
• Sd / Emmc: 2
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: Yes
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 440
• Resistive Touch Screen: Yes
• Temp. Sensor: No
• Crypto Engine: AES/DES
• Sram (kbytes): 64
• Self Program Memory: NO
• External Bus Interface: 2
• Dram Memory: DDR2/LPDDR, SDRAM/LPSDR
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 0.9 to 1.1
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

7.1
7.2
7.2.1
7.2.2
24
Memory Mapping
Embedded Memories
SAM9G46
Internal SRAM
TCM Interface
A first level of address decoding is performed by the AHB Bus Matrix, i.e., the implementation of
the Advanced High performance Bus (AHB) for its Master and Slave interfaces with additional
features.
Decoding breaks up the 4 Gbytes of address space into 16 banks of 256 Mbytes. The banks 1 to
6 are directed to the EBI that associates these banks to the external chip selects NCS0 to
NCS5.
The bank 7 is directed to the DDRSDRC0 that associates this bank to DDR_NCS chip select
and so dedicated to the 4-port DDR2/ LPDDR controller.
The bank 0 is reserved for the addressing of the internal memories, and a second level of
decoding provides 1 Mbyte of internal memory area. The bank 15 is reserved for the peripherals
and provides access to the Advanced Peripheral Bus (APB).
Other areas are unused and performing an access within them provides an abort to the master
requesting such an access.
The SAM9G46 product embeds a total of 64 Kbytes high-speed SRAM split in 4 blocks of
16 KBytes connected to one slave of the matrix. After reset and until the Remap Command is
performed, the four SRAM blocks are contiguous and only accessible at address 0x00300000.
After Remap, the SRAM also becomes available at address 0x0.
Figure 7-2.
The SAM9G46 device embeds two memory features. The processor Tightly Coupled Memory
Interface (TCM) that allows the processor to access the memory up to processor speed (PCK)
and the interface on the AHB side allowing masters to access the memory at AHB speed (MCK).
A wait state is necessary to access the TCM at 400 MHz. Setting the bit NWS_TCM in the bus
Matrix TCM Configuration Register of the matrix inserts a wait state on the ITCM and DTCM
accesses.
On the processor side, this Internal SRAM can be allocated to two areas.
0x00300000
Internal SRAM Reset
RAM
64K
Remap
RAM
64K
11028CS–ATARM–20-Apr-11
0x00000000