SAM9G46 Atmel Corporation, SAM9G46 Datasheet - Page 25

• Manufacturer Part Number: SAM9G46
• Manufacturer: Atmel Corporation

Specifications of SAM9G46

• Flash (kbytes): 0 Kbytes
• Pin Count: 324
• Max. Operating Frequency: 400 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 160
• Ext Interrupts: 160
• Usb Transceiver: 3
• Usb Speed: Hi-Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 2
• Uart: 5
• Lin: 4
• Ssc: 2
• Ethernet: 1
• Sd / Emmc: 2
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: Yes
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 440
• Resistive Touch Screen: Yes
• Temp. Sensor: No
• Crypto Engine: AES/DES
• Sram (kbytes): 64
• Self Program Memory: NO
• External Bus Interface: 2
• Dram Memory: DDR2/LPDDR, SDRAM/LPSDR
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 0.9 to 1.1
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

Table 7-1.
7.2.3
7.2.4
11028CS–ATARM–20-Apr-11
seen at 0x100000 through AHB
SRAM A ITCM size (KBytes)
Internal ROM
Boot Strategies
ITCM and DTCM Memory Configuration
32
0
0
Within the 64 Kbyte SRAM size available, the amount of memory assigned to each block is soft-
ware programmable according to
The SAM9G46 embeds an Internal ROM, which contains the bootrom and SAM-BA program.
At any time, the ROM is mapped at address 0x0040 0000. It is also accessible at address 0x0
(BMS =1) after the reset and before the Remap Command.
The system always boots at address 0x0. To ensure maximum boot possibilities the memory
layout can be changed with two parameters.
REMAP allows the user to layout the internal SRAM bank to 0x0 to ease the development. This
is done by software once the system has boot.
BMS allows the user to lay out to 0x0, when convenient, the ROM or an external memory. This is
done by a hardware way at reset.
Note: All the memory blocks can always be seen at their specified base addresses that are not
concerned by these parameters.
The SAM9G46 Bus Matrix manages a boot memory that depends on the level on the pin BMS at
reset. The internal memory area mapped between address 0x0 and 0x000F FFFF is reserved to
this effect.
If BMS is detected at 1, the boot memory is the embedded ROM.
If BMS is detected at 0, the boot memory is the memory connected on the Chip Select 0 of the
External Bus Interface.
• Internal SRAM A is the ARM926EJ-S Instruction TCM. The user can map this SRAM block
• Internal SRAM B is the ARM926EJ-S Data TCM. The user can map this SRAM block
• Internal SRAM C is only accessible by all the AHB Masters. After reset and until the Remap
anywhere in the ARM926 instruction memory space using CP15 instructions and the TCR
configuration register located in the Chip Configuration User Interface. This SRAM block is
also accessible by the ARM926 Masters and by the AHB Masters through the AHB bus
anywhere in the ARM926 data memory space using CP15 instructions. This SRAM block is
also accessible by the ARM926 Data Master and by the AHB Masters through the AHB bus.
Command is performed, this SRAM block is accessible through the AHB bus at address
0x0030 0000 by all the AHB Masters. After Remap, this SRAM block also becomes
accessible through the AHB bus at address 0x0 by the ARM926 Instruction and the ARM926
Data Masters.
seen at 0x200000 through AHB
SRAM B DTCM size (KBytes)
64
32
0
Table
7-1.
seen at 0x300000 through AHB
SRAM C (KBytes)
64
0
0
SAM9G46
25