SAM9G46 Atmel Corporation, SAM9G46 Datasheet - Page 48

• Manufacturer Part Number: SAM9G46
• Manufacturer: Atmel Corporation

Specifications of SAM9G46

• Flash (kbytes): 0 Kbytes
• Pin Count: 324
• Max. Operating Frequency: 400 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 160
• Ext Interrupts: 160
• Usb Transceiver: 3
• Usb Speed: Hi-Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 2
• Uart: 5
• Lin: 4
• Ssc: 2
• Ethernet: 1
• Sd / Emmc: 2
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: Yes
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 440
• Resistive Touch Screen: Yes
• Temp. Sensor: No
• Crypto Engine: AES/DES
• Sram (kbytes): 64
• Self Program Memory: NO
• External Bus Interface: 2
• Dram Memory: DDR2/LPDDR, SDRAM/LPSDR
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 0.9 to 1.1
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

10.4
48
Serial Synchronous Controller (SSC)
SAM9G46
• RS485 with driver control signal
• ISO7816, T = 0 or T = 1 Protocols for interfacing with smart cards
• IrDA modulation and demodulation
• SPI Mode
• LIN Mode
• Test Modes
• Provides serial synchronous communication links used in audio and telecom applications
• Contains an independent receiver and transmitter and a common clock divider
• Offers a configurable frame sync and data length
• Receiver and transmitter can be programmed to start automatically or on detection of
• Receiver and transmitter include a data signal, a clock signal and a frame synchronization
(with CODECs in Master or Slave Modes, I
different event on the frame sync signal
signal
– Receiver time-out and transmitter timeguard
– Optional Multi-drop Mode with address generation and detection
– Optional Manchester Encoding
– NACK handling, error counter with repetition and iteration limit
– Communication at up to 115.2 Kbps
– Master or Slave
– Serial Clock Programmable Phase and Polarity
– SPI Serial Clock (SCK) Frequency up to Internal Clock Frequency MCK/4
– Compliant with LIN 1.3 and LIN 2.0 specifications
– Master or Slave
– Processing of frames with up to 256 data bytes
– Response Data length can be configurable or defined automatically by the Identifier
– Self synchronization in Slave node configuration
– Automatic processing and verification of the “Synch Break” and the “Synch Field”
– The “Synch Break” is detected even if it is partially superimposed with a data byte
– Automatic Identifier parity calculation/sending and verification
– Parity sending and verification can be disabled
– Automatic Checksum calculation/sending and verification
– Checksum sending and verification can be disabled
– Support both “Classic” and “Enhanced” checksum types
– Full LIN error checking and reporting
– Frame Slot Mode: the Master allocates slots to the scheduled frames automatically.
– Generation of the Wakeup signal
– Remote Loopback, Local Loopback, Automatic Echo
2
S, TDM Buses, Magnetic Card Reader,...)
11028CS–ATARM–20-Apr-11