AD7323 Analog Devices, AD7323 Datasheet - Page 18

• Manufacturer Part Number: AD7323
• Description: 500 kSPS, 4-Channel, Software Selectable True bipolar Input, 12-Bit Plus Sign A/D Converter
• Manufacturer: Analog Devices

Specifications of AD7323

• Resolution (bits): 13bit
• # Chan: 4
• Sample Rate: 500kSPS
• Interface: Ser,SPI
• Analog Input Type: Diff-Uni,SE-Uni
• Ain Range: Bip 10V,Bip 2.5V,Bip 5.0V,Uni 10V
• Adc Architecture: SAR
• Pkg Type: SOP

AD7323
Care should be taken to ensure that the analog input does not
exceed the V
ing this value causes the diodes to become forward biased and
to start conducting into either the V
rail. These diodes can conduct up to 10 mA without causing
irreversible damage to the part.
In Figure 29 and Figure 30, Capacitor C1 is typically 4 pF and
can primarily be attributed to pin capacitance. Resistor R1 is a
lumped component made up of the on resistance of the input
multiplexer and the track-and-hold switch. Capacitor C2 is the
sampling capacitor; its capacitance varies depending on the
analog input range selected (see the Specifications section).
Track-and-Hold Section
The track-and-hold on the analog input of the AD7323 allows
the ADC to accurately convert an input sine wave of full-scale
amplitude to 13-bit accuracy. The input bandwidth of the track-
and-hold is greater than the Nyquist rate of the ADC. The
AD7323 can handle frequencies up to 22 MHz.
The track-and-hold enters its tracking mode on the 14
rising edge after the CS falling edge. The time required to
acquire an input signal depends on how quickly the sampling
capacitor is charged. With zero source impedance, 305 ns is
sufficient to acquire the signal to the 13-bit level. The
acquisition time required is calculated using the following
formula:
where C is the sampling capacitance and R is the resistance seen
by the track-and-hold amplifier looking back on the input. For
the AD7323, the value of R includes the on resistance of the
input multiplexer and is typically 300 Ω. R
any extra source impedance on the analog input.
t
ACQ
NOTES
1. V
Figure 30. Equivalent Analog Input Circuit (Differential)
= 10 × ((R
IN
V
V
+ CAN BE V
DD
IN
IN
+
–
and V
SOURCE
IN
SS
0 OR V
supply rails by more than 300 mV. Exceed-
C1
C1
+ R) C)
V
V
V
V
IN
DD
DD
SS
SS
2, AND V
D
D
D
D
IN
DD
– CAN BE V
supply rail or V
SOURCE
R1
R1
IN
1 OR V
should include
C2
C2
IN
3.
SS
th
SCLK
supply
Rev. A | Page 18 of 36
The AD7323 enters track mode on the 14
When running the AD7323 at a throughput rate of 1 MSPS with
a 10 MHz SCLK signal, the ADC has approximately
to acquire the analog input signal. The ADC goes back into
hold mode on the CS falling edge.
As the V
of the input multiplexer increases. Therefore, based on the
equation for t
acquisition time provided to the AD7323, and therefore decrease
the overall throughput rate. Figure 31 shows that as the V
V
degrades slightly. If the throughput rate is reduced when operating
with the minimum V
performance is maintained.
Unlike other bipolar ADCs, the AD7323 does not have a
resistive analog input structure. On the AD7323, the bipolar
analog signal is sampled directly onto the sampling capacitor.
This gives the AD7323 high analog input impedance. An
approximation for the analog input impedance can be
calculated from the following formula:
where f
capacitor value.
C
Specifications section). When operating at 500 kSPS, the
analog input impedance is typically 145 kΩ for the ±10 V
range. As the sampling frequency is reduced, the analog input
impedance further increases. As the analog input impedance
increases, the current required to drive the analog input
therefore decreases.
SS
S
depends on the analog input range chosen (see the
supplies are reduced, the specified THD performance
1.5 SCLK + t
Z = 1/(f
–75
–80
–85
–90
–95
S
DD
is the sampling frequency and C
Figure 31. THD vs. ±V
5
/V
S
SS
ACQ
× C
supply voltage is reduced, the on resistance
7
, it is necessary to increase the amount of
S
8
)
+ t
DD
QUIET
9
and V
±V
DD
DD
500kSPS
/V
/V
11
SS
SS
SS
supplies, the specified THD
Supply Voltage at 500 kSPS
SUPPLIES (V)
13
V
INTERNAL REFERENCE
T
f
±5V RANGE
SE MODE
IN
A
CC
S
= 25°C
= 10kHz
th
is the sampling
= V
15
SCLK rising edge.
DRIVE
= 5V
17
1
DD
9
and