AD7934 Analog Devices, AD7934 Datasheet - Page 24
![no-image](/images/manufacturer_photos/0/0/56/analog_devices_sml.jpg)
AD7934
Manufacturer Part Number
AD7934
Description
4-Channel, 1.5 MSPS, 12-Bit Parallel ADC with a Sequencer
Manufacturer
Analog Devices
Datasheet
1.AD7933.pdf
(32 pages)
Specifications of AD7934
Resolution (bits)
12bit
# Chan
4
Sample Rate
1.5MSPS
Interface
Byte,Par
Analog Input Type
Diff-Uni,SE-Uni
Ain Range
(2Vref) p-p,5V p-p,Uni (Vref),Uni (Vref) x 2,Uni 2.5V,Uni 5.0V
Adc Architecture
SAR
Pkg Type
SOP
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AD7934ARZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
AD7934BRUZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD7934BRUZ-6
Manufacturer:
Analog Devices Inc
Quantity:
135
Part Number:
AD7934BRUZ-6
Manufacturer:
ADI/亚德诺
Quantity:
20 000
AD7933/AD7934
Reading Data from the AD7933/AD7934
With the W/ B pin tied logic high, the AD7933/AD7934
interface operates in word mode. In this case, a single read
operation from the device accesses the conversion data-word on
Pin DB0 to Pin DB11 (12-bit word) and Pin DB2 to DB11
(10-bit word). The DB8/HBEN pin assumes its DB8 function.
With the W/ B pin tied to logic low, the AD7933/AD7934
interface operates in byte mode. In this case, the DB8/HBEN
pin assumes its HBEN function.
Conversion data from the AD7933/AD7934 must be accessed in
two read operations with eight bits of data provided on DB0 to
DB7 for each of the read operations. The HBEN pin determines
whether the read operation accesses the high byte or the low
byte of the 12- or 10-bit word. For a low byte read, DB0 to DB7
provide the eight LSBs of the 12-bit word. For 10-bit operation,
the two LSBs of the low byte are 0s and are followed by six bits
of conversion data. For a high byte read, DB0 to DB3 provide the
four MSBs of the 12-/10-bit word. DB4 and DB5 of the high byte
provide the Channel ID. DB6 and DB7 are always 0.
Figure 34 shows the read cycle timing diagram for a 12- or
10-bit transfer. When operating in word mode, the HBEN input
does not exist and only the first read operation is required to
access data from the device. When operating in byte mode, the
two read cycles shown in Figure 35 are required to access the
full data-word from the device.
Figure 35. AD7933/AD7934 Parallel Interface—Read Cycle Timing for Byte Mode Operation (W/ B = 0)
DB0 TO DB7
HBEN/DB8
RD
CS
t
t
13
15
t
10
LOW BYTE
t
12
Rev. B | Page 24 of 32
t
11
t
16
t
14
The CS and RD signals are gated internally and the level is
triggered active low. In either word mode or byte mode, CS and
RD can be tied together as the timing specifications for t
t
by the AD7933/AD7934.
The data is placed onto the data bus a time t
RD go low. The RD rising edge can be used to latch data out of
the device. After a time, t
Alternatively, CS and RD can be tied permanently low, and the
conversion data is valid and placed onto the data bus a time, t
before the falling edge of BUSY.
Note that if RD is pulsed during the conversion time, this
causes a degradation in linearity performance of approximately
0.25 LSB. Reading during conversion, by way of tying CS and
RD low, does not cause any degradation.
11
t
17
are 0 ns minimum. This means the bus is constantly driven
t
15
HIGH BYTE
14
, the data lines become three-stated.
t
16
13
after both CS and
10
and
9
,