AD5363 Analog Devices, AD5363 Datasheet - Page 24

• Manufacturer Part Number: AD5363
• Description: 8-Channel, 14-Bit, Serial Input, Voltage-Output DAC
• Manufacturer: Analog Devices

Specifications of AD5363

• Resolution (bits): 14bit
• Dac Settling Time: 20µs
• Single-supply: No
• Dac Type: Voltage Out
• Dac Input Format: Ser,SPI

AD5362/AD5363
SPECIAL FUNCTION MODE
If the mode bits are 00, the special function mode is selected, as shown in Table 15. Bit I21 to Bit I16 of the serial data-word select the
special function, and the remaining bits are data required for execution of the special function, for example, the channel address for data
readback. The codes for the special functions are shown in Table 16. Table 17 shows the addresses for data readback.
Table 15. Special Function Mode
I23
0
Table 16. Special Function Codes
S5
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Special Function Code
S4
0
0
0
0
0
0
0
0
0
0
0
0
0
0
I22
0
S3
0
0
0
0
0
0
0
0
1
1
1
1
1
1
I21
S5
S2
0
0
0
0
1
1
1
1
0
0
0
0
1
1
I20
S4
S1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
I19
S3
S0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
I18
S2
Data (F15 to F0)
0000 0000 0000 0000
XXXX XXXX XXXX X [F2:F0]
XX [F13:F0]
XX [F13:F0]
Reserved
See Table 17
XXXX XXXX XXXX [F3:F0]
XXXX XXXX XXXX [F3:F0]
Reserved
Reserved
Reserved
XXXX XXXX [F7:F0]
XXXX XXXX XX [F5:F0]
XXXX XXXX XXXX XX [F1:F0]
I17
S1
I16
S0
I15
F15
I14
F14
Rev. A | Page 24 of 28
I13
F13
Action
NOP.
Write control register.
F4 = 1: Temperature over 130°C.
F4 = 0: Temperature below 130°C.
Read-only bit. This bit should be 0 when writing to the control register.
F3 = 1: PEC error.
F3 = 0: No PEC error. Reserved.
Read-only bit. This bit should be 0 when writing to the control register.
F2 = 1: Select Register X1B for input.
F2 = 0: Select Register X1A for input.
F1 = 1: Enable thermal shutdown mode.
F1 = 0: Disable thermal shutdown mode.
F0 = 1: Software power-down.
F0 = 0: Software power-up.
Write data in F13 to F0 to OFS0 register.
Write data in F13 to F0 to OFS1 register.
Select register for readback.
Write data in F3 to F0 to A/B Select Register 0.
Write data in F3 to F0 to A/B Select Register 1.
Block write to A/B select registers.
F7 to F0 = 0: Write all 0s (all channels use X2A register).
F7 to F0 = 1: Write all 1s (all channels use X2B register).
F5 = 1: Monitor enable.
F5 = 0: Monitor disable.
F4 = 1: Monitor input pin selected by F0.
F4 = 0: Monitor DAC channel selected by F3:F0 (see Table 10).
F3 = not used if F4 = 1.
F2 = not used if F4 = 1.
F1 = not used if F4 = 1.
F0 = 0: MON_IN0 selected for monitoring (if F4 and F5 = 1).
F0 = 1: MON_IN1 selected for monitoring (if F4 and F5 = 1).
GPIO configure and write.
F1 = 1: GPIO is an output. Data to output is written to F0.
F1 = 0: GPIO is an input. Data can be read from F0 on readback.
I12
F12
I11
F11
I10
F10
I9
F9
I8
F8
I7
F7
I6
F6
I5
F5
I4
F4
I3
F3
I2
F2
I1
F1
I0
F0