AD7249 Analog Devices, AD7249 Datasheet - Page 7
![no-image](/images/manufacturer_photos/0/0/56/analog_devices_sml.jpg)
AD7249
Manufacturer Part Number
AD7249
Description
LC2MOS Dual 12-Bit Serial DACPORT
Manufacturer
Analog Devices
Datasheet
1.AD7249.pdf
(12 pages)
Specifications of AD7249
Resolution (bits)
12bit
Dac Update Rate
125kSPS
Dac Settling Time
7µs
Max Pos Supply (v)
+16.5V
Single-supply
Yes
Dac Type
Voltage Out
Dac Input Format
Ser
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AD7249AR
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
AD7249ARZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
AD7249ARZ-REEL
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
AD7249BRZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD7249BRZ-REEL
Manufacturer:
VISHAY
Quantity:
2 000
Company:
Part Number:
AD7249SQ
Manufacturer:
SILICON
Quantity:
15 000
Part Number:
AD7249SQ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
DIGITAL INTERFACE
The AD7249 contains an input serial to parallel shift register
and a DAC latch for both DAC A and DAC B. A simplified
diagram of the input loading circuitry is shown in Figure 7.
Serial data on the SDIN input is loaded to the input register
under control of SYNC and SCLK. The SYNC input provides
the frame synchronization signal which tells the AD7249 that
valid serial data on the SDIN input will be available for the next
16 falling edges of SCLK. An internal counter/decoder circuit
provides a low gating signal so that only 16 data bits are clocked
into the input shift register. After 16 SCLK pulses the internal
gating signal goes inactive (high) thus locking out any further
clock pulses. Therefore either a continuous clock or a burst
clock source may be used to clock in the data. The SYNC input
is taken high after the complete 16-bit word is loaded in.
DAC selection is accomplished using the thirteenth bit (DB12)
of the serial data input stream. A zero in DB12 will select DAC
A while a one in this position selects DAC B. Although 16 bits
of data are clocked into the input register, only 12 bits get trans-
ferred into the DAC latch. The relevant DAC latch is deter-
mined by the value of the thirteenth bit and the first three bits
in the 16-bit stream are don’t cares. Therefore, the data format
is three don’t cares followed by the DAC selection bit and the
12-bit data word with the LSB as the last bit in the serial
stream.
SYNC
SCLK
LDAC
SDIN
CLR
DECOUNTER
RESET
COUNTER/
AUTO-UPDATE
CIRCUITRY
/16
GATING
SIGNAL
DECODER
CLK A
SDATA
CLK B
There are two ways in which a DAC latches and hence the
analog outputs may be updated. The status of the LDAC input
is examined after SYNC is taken low. Depending on its status,
one of two update modes are selected.
If LDAC = 0, then the automatic update mode is selected. In
this mode the DAC latch and analog output are updated auto-
matically when the last bit in the serial data stream is clocked in.
The update thus takes place on the sixteenth falling SCLK edge.
If LDAC = 1, then the automatic update is disabled and both
DAC latches are updated by taking LDAC low any time after
the 16-bit data transfer is complete. The update now occurs on
the falling edge of LDAC. Note that the LDAC input must be
taken back high again before the next data transfer is initiated.
When a complete word is held in the shift register it may then
be loaded into the DAC latch under control of LDAC.
Clear Function (CLR)
The clear function clears the contents of the input shift register
and loads both DAC latches with all 0s. It is activated by taking
CLR low. In all ranges except the Offset Binary bipolar range
(–5 V to +5 V) the output voltage is reset to 0 V. In the offset
binary bipolar range the output is set to –REFIN. The clear
function is especially useful at power-up as it enables the output
to be reset to a known state.
DAC LATCH A (12-BITS)
DAC LATCH B (12-BITS)
SHIFT REGISTER A
SHIFT REGISTER B
AD7249