STM32F103T8 STMicroelectronics, STM32F103T8 Datasheet - Page 39

no-image

STM32F103T8

Manufacturer Part Number
STM32F103T8
Description
Mainstream Performance line, ARM Cortex-M3 MCU with 64 Kbytes Flash, 72 MHz CPU, motor control, USB and CAN
Manufacturer
STMicroelectronics
Datasheet

Specifications of STM32F103T8

Conversion Range
0 to 3.6 V
Peripherals Supported
timers, ADC, SPIs, I2Cs and USARTs

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
STM32F103T8
Manufacturer:
ST
0
Part Number:
STM32F103T8T6
Manufacturer:
ST
0
Part Number:
STM32F103T8U6
Manufacturer:
ST
Quantity:
13 000
Part Number:
STM32F103T8U6
Manufacturer:
STMicroelectronics
Quantity:
20 000
Part Number:
STM32F103T8U6
Manufacturer:
STMicroelectronics
Quantity:
10 000
Part Number:
STM32F103T8U6TR
Manufacturer:
STMicroelectronics
Quantity:
10 000
Part Number:
STM32F103T8U6TR
Manufacturer:
ST
0
Part Number:
STM32F103T8U7
Manufacturer:
ST
Quantity:
100
Part Number:
STM32F103T8U7
Manufacturer:
ST
Quantity:
3 739
Price:
7.15 USD
STM32F103x8, STM32F103xB
5.3.4
5.3.5
Embedded reference voltage
The parameters given in
temperature and V
Table 12.
1. Shortest sampling time can be determined in the application by multiple iterations.
2. Guaranteed by design, not tested in production.
Supply current characteristics
The current consumption is a function of several parameters and factors such as the
operating voltage, ambient temperature, I/O pin loading, device software configuration,
operating frequencies, I/O pin switching rate, program location in memory and executed
binary code.
The current consumption is measured as described in
measurement
All Run-mode current consumption measurements given in this section are performed with a
reduced code that gives a consumption equivalent to Dhrystone 2.1 code.
Maximum current consumption
The MCU is placed under the following conditions:
The parameters given in
under ambient temperature and V
T
V
Symbol
V
S_vrefint
T
RERINT
REFINT
Coeff
All I/O pins are in input mode with a static value at V
All peripherals are disabled except when explicitly mentioned
The Flash memory access time is adjusted to the f
to 24 MHz, 1 wait state from 24 to 48 MHz and 2 wait states above)
Prefetch in ON (reminder: this bit must be set before clock setting and bus prescaling)
When the peripherals are enabled f
(2)
(2)
(1)
Internal reference voltage
ADC sampling time when
reading the internal reference
voltage
Internal reference voltage
spread over the temperature
range
Temperature coefficient
Embedded internal reference voltage
scheme.
DD
Parameter
supply voltage conditions summarized in
Table 12
Table
Doc ID 13587 Rev 13
13,
DD
are derived from tests performed under ambient
Table 14
supply voltage conditions summarized in
PCLK1
–40 °C < T
–40 °C < T
V
and
DD
Conditions
= f
= 3 V ±10 mV
Table 15
HCLK
A
A
< +105 °C
< +85 °C
/2, f
Figure 14: Current consumption
HCLK
DD
are derived from tests performed
PCLK2
or V
frequency (0 wait state from 0
Table
1.16
1.16
Min
= f
SS
Electrical characteristics
HCLK
(no load)
9.
1.20
1.20
Typ
5.1
17.1
1.26
1.24
Max
100
10
Table
(2)
ppm/°C
9.
Unit
mV
µs
V
V
39/99

Related parts for STM32F103T8