STR751FR2 STMicroelectronics, STR751FR2 Datasheet - Page 33
![no-image](/images/manufacturer_photos/0/6/637/stmicroelectronics_sml.jpg)
STR751FR2
Manufacturer Part Number
STR751FR2
Description
ARM7TDMI-S™ 32-BIT MCU with Flash, SMI, 3 std 16-bit timers, PWM timer, fast 10-bit ADC, I2C, UART, SSP, USB and CAN
Manufacturer
STMicroelectronics
Datasheet
1.STR755FV2.pdf
(84 pages)
Specifications of STR751FR2
Smart Low Power Modes
SLOW, WFI, STOP and STANDBY with backup registers
Conversion Time
min. 3.75 μs
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
STR751FR2H6
Manufacturer:
STMicroelectronics
Quantity:
10 000
Company:
Part Number:
STR751FR2T6
Manufacturer:
ST
Quantity:
10 000
Company:
Part Number:
STR751FR2T6
Manufacturer:
STMicroelectronics
Quantity:
10 000
Part Number:
STR751FR2T6
Manufacturer:
ST
Quantity:
20 000
STR750Fxx STR751Fxx STR752Fxx STR755Fxx
6.2.2
6.2.3
Current characteristics
Table 8.
1. The user can use GPIOs to source or sink high current (up to 20 mA for O8 type High Sink I/Os). In this
2. All 3.3 V or 5.0 V power (V
3. I
4. Negative injection disturbs the analog performance of the device. See note in
5. When several inputs are submitted to a current injection, the maximum ΣI
Thermal characteristics
Table 9.
I
INJ(PIN)
case, the user must ensure that these absolute max. values are not exceeded (taking into account the
RUN power consumption) and must follow the rules described in
on page
must always be connected to the external 3.3V or 5.0V supply.
cannot be respected, the injection current must be limited externally to the I
injection is induced by V
characteristics on page
positive and negative injected currents (instantaneous values). These results are based on
characterization with ΣI
ΣI
INJ(PIN)
I
I
VDD_IO
Symbol
Symbol
VSS_IO
INJ(PIN)
T
I
STG
T
IO
J
(3) & (4)
must never be exceeded. This is implicitly insured if V
54.
(1)
(1)
(3)
Current characteristics
Thermal characteristics
Total current into V
Total current out of V
Output current sunk by any I/O and control pin
Output current source by any I/Os and control pin
Injected current on NRSTIN pin
Injected current on XT1 and XT2 pins
Injected current on any other pin
Total injected current (sum of all I/O and control pins)
INJ(PIN)
72.
IN
>V
DD_IO
Maximum junction temperature
DD
Storage temperature range
maximum current injection on four I/O port pins of the device.
while a negative injection is induced by V
, V
DDA_ADC
DD_IO
Ratings
SS
, V
ground lines (sink)
power lines (source)
DDA_PLL
Ratings
) and ground (V
(5)
IN
maximum is respected. If V
Section 6.3.8: I/O port pin characteristics
(2)
(2)
SS_IO
INJ(PIN)
IN
<V
INJ(PIN)
, V
SS
Section 6.3.12: 10-bit ADC
SSA_ADC
(5)
-65 to +150
. Data based on T
is the absolute sum of the
Electrical parameters
value. A positive
Value
150
, V
Maximum
value
DDA_ADC
± 25
- 25
150
150
± 5
± 5
± 5
25
IN
maximum
A
) pins
=25°C.
Unit
Unit
°C
°C
mA
33/84