FSCM0565R Fairchild Semiconductor, FSCM0565R Datasheet
![no-image](/images/manufacturer_photos/0/2/252/fairchild_semiconductor_sml.jpg)
FSCM0565R
Available stocks
Related parts for FSCM0565R
FSCM0565R Summary of contents
Page 1
... SMPS for VCR, SVR, STB, DVD & DVCD • Adaptor • SMPS for LCD Monitor Description The FSCM0565R is an integrated Pulse Width Modulator (PWM) and Sense FET specifically designed for high performance offline Switch Mode Power Supplies (SMPS) with minimal external components. This device is an ...
Page 2
... Internal Block Diagram 0.3/0. Vcc Vcc I I delay FB 2. limit 5 Soft start 0. Vcc Vovp TSD Vcc UV reset Figure 2. Functional Block Diagram of FSCM0565R 2 Vcc 3 Vcc good 8V/12V Freq. Modulation OSC PWM Vcc good R Q Drain 1 Internal Vref Bias ...
Page 3
... This pin is for the pulse by pulse current limit level programming. By using a resistor to GND on this pin, the current limit level can be changed. If this pin is left floating, the typical current limit will be 2.5A. Figure 3. Pin Configuration (Top View) FSCM0565R FSCM0565RC TO-220-5L 5. I_limit Vcc 2 ...
Page 4
... FSCM0565R Absolute Maximum Ratings (Ta=25 C, unless otherwise specified) Parameter (1) Drain-Source (GND) Voltage Drain-Gate Voltage (R = Gate-Source (GND) Voltage (2) Drain Current Pulsed Continuous Drain Current (TO-220 25° =100 C C Continuous Drain Current (D2-PAK 25° =100 C C Supply Voltage Analog Input Voltage Range ...
Page 5
... mod T - mod F 10V V 17V STABLE +85 C OSC D - MAX D - MIN V V =GND START =GND STOP =GND Vcc=14V BH VB Vcc=14V L FSCM0565R Min. Typ. Max. Unit 650 - - 500 A - 1.76 2 kHz - ±3 - kHz - ...
Page 6
... FSCM0565R PROTECTION SECTION Peak current limit Over voltage protection Thermal shutdown temperature Shutdown delay current Shutdown feedback voltage TOTAL DEVICE SECTION Startup current Operating supply current Notes: 1. Pulse test : Pulse width 300 S, duty 2. These parameters, although guaranteed at the design, are not tested in mass production. ...
Page 7
... Comparison Between FSDM0565RB and FSCM0565R Function Frequency modulation N.A. Pulse-by-pulse current limit • Internally fixed (2.25A) Internal Startup Circuit • Available FSDM0565RB Available • Modulated frequency range (DF • Frequency modulation cycle (T • Programmable using external resistor (2.5A max) • N.A. (Requires startup resistor) • ...
Page 8
... FSCM0565R Typical Performance Characteristics (These Characteristic Graphs are Normalized at Ta 1.60 1.40 1.20 1.00 0.80 0.60 -50 - Junction Temperature Startup Current vs. Temp 1.20 1.12 1.04 0.96 0.88 0.80 -50 - Junction Temperature Stop Threshold Voltage vs. Temp 1.20 1.12 1.04 0.96 0.88 0.80 -50 - Junction Temperature Maximum Duty Cycle vs. Temp 8 1.20 1.12 1.04 0.96 0.88 0.80 75 100 125 -50 Start Threshold Voltage vs. Temp 1 ...
Page 9
... Mavimum Drain Current vs. Temp (Continued) 1.20 1.12 1.04 0.96 0.88 0.80 75 100 125 -50 ShutDown Delay Current vs. Temp 1.20 1.12 1.04 0.96 0.88 0.80 75 100 125 -50 Burst Mode Disable Voltage vs. Temp 1.20 1.12 1.04 0.96 0.88 0.80 -50 75 100 125 Operating Supply Current vs. Temp FSCM0565R - 100 125 Junction T emperature - 100 125 Junction Temperature - 100 125 Junction Temperature ...
Page 10
... I maximum startup current (40uA). If not, Vcc can not be charged to the start voltage and FPS will fail to start up. 2. Feedback Control : FSCM0565R employs current mode control, as shown in Figure 6. An opto-coupler (such as the H11A817A) and shunt regulator (such as the KA431) are typically used to implement the feedback network ...
Page 11
... DC link charges the external capacitor (C ) that is connected to the Vcc pin. When Vcc a reaches the start voltage of 12V, FSCM0565R resumes its normal operation. In this manner, the auto-restart can alternately enable and disable the switching of the power Sense FET until the fault condition is eliminated (see Figure 7) ...
Page 12
... Figure 9. Frequency Modulation 5. Soft Start : The FSCM0565R has an internal soft start circuit that increases PWM comparator inverting input voltage together with the Sense FET current slowly after it starts up. The typical soft start time is 15msec, The pulse width to the power switching device is progressively increased to establish the correct working conditions for transformers, rectifier diodes and capacitors ...
Page 13
... UF 4007 3 FSCM0565RC 5 1 Drain I limit 3 Vcc 4 Vfb 4 D102 R104 GND C105 TVR10G 22uF ZD101 50V 22V 5 FSCM0565R Output voltage (Max current) 5V (2.0A) 12V (2.5A) D202 T1 L201 MBRF10100 EER3016 12V, 2.5A 10 C202 C201 1000uF 1000uF 25V 25V 8 D201 L202 MBRF1045 7 C204 C203 1000uF 1000uF ...
Page 14
... FSCM0565R 2. Transformer Schematic Diagram 3.Winding Specification No Pin ( Insulation: Polyester Tape t = 0.050mm, 2Layers Np Insulation: Polyester Tape t = 0.050mm, 2Layers 12V Insulation: Polyester Tape t = 0.050mm, 2Layers N5V 7 6 Insulation: Polyester Tape t = 0.050mm, 2Layers Np Outer Insulation: Polyester Tape t = 0.050mm, 2Layers 4 ...
Page 15
... LF101 IC101 FSCM0565RC IC201 KA431(TL431) IC301 Value Note 4.7nF Polyester Film Cap. Inductor 5uH Wire 1.2mm 5uH Wire 1.2mm Diode UF4007 TVR10G MBRF1045 MBRF10100 Bridge Diode Bridge Diode Line Filter 23mH Wire 0.4mm IC TM FPS (7A,650V) Voltage reference H11A817A Opto-coupler FSCM0565R 15 ...
Page 16
... FSCM0565R 7. Layout Figure 11. Layout Considerations for FSCM0565RC Figure 12. Layout Considerations for FSCM0565RC 16 ...
Page 17
... Package Dimensions D2-PAK-5L FSCM0565R 17 ...
Page 18
... FSCM0565R Package Dimensions (Continued) 18 TO-220-5L(Forming) ...
Page 19
... Ordering Information Product Number Package FSCM0565RD D2-PAK-5L FSCM0565RCYDTU TO-220-5L Marking Code BVdss CM0565RD 650V CM0565RC 650V FSCM0565R Rds(on)Max. 2.2 2.2 19 ...
Page 20
... FSCM0565R DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. ...