ADSP-21060 Analog Devices, ADSP-21060 Datasheet - Page 17

• Manufacturer Part Number: ADSP-21060
• Description: ADSP-2106x SHARC DSP Microcomputer Family
• Manufacturer: Analog Devices

ABSOLUTE MAXIMUM RATINGS (5 V)*
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V
Input Voltage . . . . . . . . . . . . . . . . . . . . –0.5 V to V
Output Voltage Swing . . . . . . . . . . . . . –0.5 V to V
Load Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 pF
Junction Temperature Under Bias . . . . . . . . . . . . . . . . 130°C
Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C
Lead Temperature (5 seconds) . . . . . . . . . . . . . . . . . +280°C
*Stresses greater than those listed above may cause permanent damage to the
ESD SENSITIVITY
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the ADSP-2106x features proprietary ESD protection circuitry, permanent damage may occur on
devices subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.
TIMING SPECIFICATIONS
Two speed grades of the ADSP-21060 are offered, 40 MHz and
33.3 MHz. The specifications shown are based on a CLKIN
frequency of 40 MHz (t
specifications at other CLKIN frequencies (within the min–max
range of the t
the difference between the actual CLKIN period and a CLKIN
period of 25 ns:
Use the exact timing information given. Do not attempt to
derive parameters from the addition or subtraction of others.
While addition or subtraction would yield meaningful results for
an individual device, the values given in this data sheet reflect
statistical variations and worst cases. Consequently, you cannot
meaningfully add parameters to derive longer times.
device. These are stress ratings only, and functional operation of the device at these
or any other conditions greater than those indicated in the operational sections of
this specification is not implied. Exposure to absolute maximum rating conditions
for extended periods may affect device reliability.
CK
specification; see Clock Input below). DT is
CK
DT = t
= 25 ns). The DT derating allows
CK
– 25 ns
DD
DD
+ 0.5 V
+ 0.5 V
ABSOLUTE MAXIMUM RATINGS (3.3 V)*
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +4.6 V
Input Voltage . . . . . . . . . . . . . . . . . . . . –0.5 V to V
Output Voltage Swing . . . . . . . . . . . . . –0.5 V to V
Load Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 pF
Junction Temperature Under Bias . . . . . . . . . . . . . . . . 130°C
Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C
Lead Temperature (5 seconds) . . . . . . . . . . . . . . . . . +280°C
*Stresses greater than those listed above may cause permanent damage to the
See Figure 28 under Test Conditions for voltage reference
levels.
Switching Characteristics specify how the processor changes its
signals. You have no control over this timing—circuitry external
to the processor must be designed for compatibility with these
signal characteristics. Switching characteristics tell you what the
processor will do in a given circumstance. You can also use
switching characteristics to ensure that any timing requirement
of a device connected to the processor (such as memory) is
satisfied.
Timing Requirements apply to signals that are controlled by cir-
cuitry external to the processor, such as the data input for a
read operation. Timing requirements guarantee that the proces-
sor operates correctly with other devices.
(O/D) = Open Drain
(A/D) = Active Drive
device. These are stress ratings only, and functional operation of the device at these
or any other conditions greater than those indicated in the operational sections of
this specification is not implied. Exposure to absolute maximum rating conditions
for extended periods may affect device reliability.
ADSP-21060/ADSP-21060L
WARNING!
ESD SENSITIVE DEVICE
DD
DD
+ 0.5 V
+ 0.5 V