nRF24LE1 Nordic VLSI, nRF24LE1 Datasheet - Page 71
![no-image](/images/no-image-200.jpg)
nRF24LE1
Manufacturer Part Number
nRF24LE1
Description
Manufacturer
Nordic VLSI
Datasheet
1.NRF24LE1.pdf
(191 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
nRF24LE1-017Q24-R7
Manufacturer:
NORDIC
Quantity:
20 000
Company:
Part Number:
nRF24LE1-017Q32-R
Manufacturer:
NORDIC
Quantity:
1 534
Part Number:
nRF24LE1-017Q32-R7
Manufacturer:
NORDIC
Quantity:
20 000
Company:
Part Number:
nRF24LE1-F16Q32-R
Manufacturer:
VISHAY
Quantity:
50 000
Company:
Part Number:
nRF24LE1-F16Q48
Manufacturer:
OKI
Quantity:
2 850
Part Number:
nRF24LE1-F16Q48-R
Manufacturer:
NORDIC
Quantity:
20 000
Part Number:
nRF24LE1-O17Q24-R7
Manufacturer:
NORDIC
Quantity:
20 000
Part Number:
nRF24LE1-O17Q24-T
Manufacturer:
NORDIC
Quantity:
20 000
Company:
Part Number:
nRF24LE1-O17Q48
Manufacturer:
GENERAL
Quantity:
795
Company:
Part Number:
nRF24LE1D
Manufacturer:
INFINEON
Quantity:
67 000
nRF24LE1 Preliminary Product Specification
written a minimum of 20000 times as opposed to 1000 for the ‘normal’ flash based NVM. The different
parts of the memory can be accessed by the MCU through normal code and data space operations.
Configuration and setup of the memory behavior during normal mode (that is, when MCU is running appli-
cation code) is defined by data stored in a separate InfoPage. During the chip reset/start-up sequence the
configuration data in the InfoPage is read and stored in the memory configuration SFR’s.
6.3.1
The on-chip flash memory is divided into 2 blocks, the 16k + 1.5k NVM main block (MB) and a 512 byte
Information Page (IP).
The memory configuration is stored in the InfoPage (IP) and the following configuration can be done:
All configuration of the flash memory must be done through the external SPI interface. The configuration
information is stored in the InfoPage during programming of the device and is read out to the flash configu-
ration SFR’s during each reset/startup sequence of the circuit.
6.3.1.1
The InfoPage is a separate page (512bytes) of flash memory that contain Nordic system tuning parame-
ters and the configurable options of the flash memory. Any changes to the flash memory configuration
must be done by updating this page. The InfoPage content is as follows:
Revision 1.1
Device system
Number of unprotected
pages: NUPP
(page address of start of
protected area)
Reserved
Flash main block read
back protect
1.
2.
3.
InfoPage data
Split the code space of the main block into 2 areas, protected and unprotected (against MCU
Disable Read and Write access to the flash from external interfaces SPI and HW debug.
Enable HW debug features.
erase/write operations).
Flash memory configuration
InfoPage content
RDISMB
DSYS
Name
NUPP
-
a
32 bytes
2 bytes
1 byte
1 byte
Size
71 of 191
Address
0x00
0x20
0x21
0x23
Reserved for device use. Do not erase or
modify.
Read out to register FPCR during start up
NUPP=0xFF: all pages are unprotected
Reserved, must be 0xFF
Disable flash main block access from external
interfaces (SPI, HW debug).
Byte value:
Can only be changed once by SPI command
RDISMB. Can only be reset by SPI command
ERASE ALL
•
•
0xFF: Flash main block accessible from
external interfaces
Other value: No read/erase/write of
flash main block from external inter-
faces. Only read of info page
Comment