IDT82V2044E Integrated Device Technology, IDT82V2044E Datasheet - Page 18
![no-image](/images/no-image-200.jpg)
IDT82V2044E
Manufacturer Part Number
IDT82V2044E
Description
4 Channel T1/j1/e1 Short Haul Liu
Manufacturer
Integrated Device Technology
Datasheet
1.IDT82V2044E.pdf
(73 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
IDT82V2044EPF
Manufacturer:
IDT, Integrated Device Technology Inc
Quantity:
10 000
Company:
Part Number:
IDT82V2044EPF8
Manufacturer:
IDT, Integrated Device Technology Inc
Quantity:
10 000
Company:
Part Number:
IDT82V2044EPFG
Manufacturer:
BOSANHITE
Quantity:
462
Company:
Part Number:
IDT82V2044EPFG
Manufacturer:
IDT
Quantity:
353
Company:
Part Number:
IDT82V2044EPFG
Manufacturer:
IDT, Integrated Device Technology Inc
Quantity:
10 000
Company:
Part Number:
IDT82V2044EPFG8
Manufacturer:
IDT, Integrated Device Technology Inc
Quantity:
10 000
QUAD CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
3.2.4
impedance matching can be realized by the internal impedance matching
circuit or the external impedance matching circuit. If T_TERM[2] is set to
‘0’, the internal impedance matching circuit will be selected. In this case,
the T_TERM[1:0] bits (TERM, 1AH...) can be set to choose 75 Ω, 100 Ω,
110 Ω or 120 Ω internal impedance of TTIPn/TRINGn. If T_TERM[2] is set
to ‘1’, the internal impedance matching circuit will be disabled. In this case,
the external impedance matching circuit will be used to realize the imped-
ance matching. For T1/J1 mode, the external impedance matching circuit
for the transmitter is not supported.
components to connect with the cable for one channel.
Table-10 Impedance Matching for Transmitter
3.2.5
T_OFF bit (TCF0, 02H...) to ‘1’. In this case, the TTIPn/TRINGn pins are
turned into high impedance.
The transmit line interface consists of TTIPn pin and TRINGn pin. The
Note: The precision of the resistors should be better than ± 1%
The transmit path can be powered down individually by setting the
Cable Configuration
TRANSMIT PATH LINE INTERFACE
TRANSMIT PATH POWER DOWN
T1/133~266 ft
T1/266~399 ft
T1/399~533 ft
T1/533~655 ft
T1/0~133 ft
J1/0~655 ft
E1/120 Ω
E1/75 Ω
Figure-8
T_TERM[2:0]
000
001
010
shows the appropriate external
011
Internal Termination
Table-10
PULS[3:0]
0000
0001
0010
0011
0100
0101
0110
0111
is the list
18
of the recommended impedance matching for transmitter.
ing THZ pin to high or individually by setting the THZ bit (TCF1, 03H...) to
‘1’. In this state, the internal transmit circuits are still active.
impedance:
•
•
•
•
0 Ω
R
The TTIPn/TRINGn can be turned into high impedance globally by pull-
Besides, in the following cases, TTIPn/TRINGn will also become high
T
Loss of MCLK: all TTIPn/TRINGn pins become high impedance;·
Loss of TCLKn: corresponding TTIPn/TRINGn become HZ (excep-
tions: Remote Loopback; Transmit internal pattern by MCLK);
Transmit path power down;
After software reset; pin reset and power on.
T_TERM[2:0]
1XX
-
External Termination
PULS[3:0]
0001
0001
-
TEMPERATURE RANGES
INDUSTRIAL
9.4 Ω
R
-
T