cs8952t Cirrus Logic, Inc., cs8952t Datasheet - Page 66
cs8952t
Manufacturer Part Number
cs8952t
Description
100base 10base-t Transceiver
Manufacturer
Cirrus Logic, Inc.
Datasheet
1.CS8952T.pdf
(86 pages)
- Current page: 66 of 86
- Download datasheet (774Kb)
•
•
66
ly) on both sides of the TX+/- traces.
No signal current carrying planes, i.e. no
ground or power plane, should be present un-
derneath the region between the transformer
secondary (network) side and the RJ-45. How-
ever, a chassis plane may be added in this re-
gion to pick up the metal tabs of a shielded RJ-
45. This chassis plane should be separated from
the ground and power planes by at least
50 mils. That is, all other ground and power
planes should be “cookie cuttered” so they are
voided in the area of the chassis plane. Gener-
ally speaking, parts should not cross the moat
except for the transformer.
Proper termination practices must be used with
all transmission lines, especially if sending/re-
ceiving high speed signals. Series terminations
must be kept close to the source and load termi-
CS8952T Pin
Assignment
91 (RX+)
80 (TX+)
92 (RX-)
81 (TX-)
CIRRUS LOGIC ADVANCED PRODUCT DATABOOK
T1 Primary Pin
Assignment
15 (TX+)
16 (TX-)
1 (RX+)
2 (RX-)
Table 11. RJ-45 Wiring
Pin Assignment
T1 Secondary
CrystalLAN™ 100BASE-X and 10BASE-T Transceiver
11 (TX+)
10 (TX-)
7 (RX+)
6 (RX-)
•
•
•
nations close to the load.
Locate the crystal as close to the CS8952T as
possible, running short traces on the compo-
nent side in order to reduce parasitic load ca-
pacitance.
Add bulk capacitance at each connector where
power may be supplied. For example, MII pow-
er may be provided at the MII connector and at
a separate connector for test purposes. If so,
and the two connectors are not adjacent, then
the bulk capacitors should be duplicated in each
locations.
Use wide traces to connect the unused pairs ter-
mination resistors at T1 and the RJ-45 to the
2 KV capacitor or capacitors in order to mini-
mize their lead inductance.
Configuration
Adapter/NIC
3 (RD+)
1 (TD+)
6 (RD-)
2 (TD-)
RJ-45 Pin Assignment
Hub/Repeater
Configuration
1 (RD+)
3 (TD+)
2 (RD-)
6 (TD-)
DS206TPP2
CS8952T
Related parts for cs8952t
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Cs-series B7a Interface Unit
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Cs-series Compobus/s Master Unit
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Cs Series Analog I/o Unit
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Cirrus Logic [Multi-Channel Digital Audio Decoders]
Manufacturer:
Cirrus Logic, Inc.
Datasheet:
Part Number:
Description:
CS492405-CLCirrus Logic [Multi-Channel Digital Audio Decoders]
Manufacturer:
Cirrus Logic, Inc.
Datasheet:
Part Number:
Description:
16-bit, 20kHz oversampling A/D converter
Manufacturer:
Cirrus Logic, Inc.
Datasheet:
Part Number:
Description:
Crystal clear PCI audio interface
Manufacturer:
Cirrus Logic, Inc.
Datasheet:
Part Number:
Description:
16, 14 & 12-Bit, Self-Calibrating A/D Converters
Manufacturer:
Cirrus Logic, Inc.
Datasheet:
Part Number:
Description:
Multi-standard audio decoder
Manufacturer:
Cirrus Logic, Inc.
Datasheet:
Part Number:
Description:
E1 line interface unit
Manufacturer:
Cirrus Logic, Inc.
Datasheet:
Part Number:
Description:
DVD on-a-chip solution
Manufacturer:
Cirrus Logic, Inc.
Datasheet:
Part Number:
Description:
Digital audio interface receiver
Manufacturer:
Cirrus Logic, Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
Cirrus Logic, Inc.
Datasheet:
Part Number:
Description:
DVD processor for low cost DVD players
Manufacturer:
Cirrus Logic, Inc.
Datasheet:
Part Number:
Description:
16-bit multimedia audio codec
Manufacturer:
Cirrus Logic, Inc.
Datasheet: