pca9952 NXP Semiconductors, pca9952 Datasheet

pca9952

Manufacturer Part Number

pca9952

Description

16-channel Fm+ I 2c-bus 57 Ma Constant Current Led Driver

Manufacturer

NXP Semiconductors

Datasheet

1.PCA9952.pdf (45 pages)

Available stocks

Company

Part Number

Manufacturer

Quantity

Price

Company:

Bonase Electronics (HK) Co., Limited

Part Number:

pca9952TW,118

Manufacturer:

ALLEGRO

Quantity:

101

Company:

Amily Shenzhen XNWY Technology Co., Ltd

Part Number:

pca9952TW/Q900

Company:

Meier Automation Equipment Co., Limited

Part Number:

pca9952TW/Q900,118

Manufacturer:

NXP/恩智浦

Quantity:

20 000

Current page: 1 of 45
Download datasheet (2Mb)

1. General description

The PCA9952 and PCA9955 are I

driver optimized for dimming and blinking 57 mA Red/Green/Blue/Amber (RGBA) LEDs in

amusement products. Each LEDn output has its own 8-bit resolution (256 steps) fixed

frequency individual PWM controller that operates at 31.25 kHz with a duty cycle that is

adjustable from 0 % to 99.6 % to allow the LED to be set to a specific brightness value. An

additional 8-bit resolution (256 steps) group PWM controller has both a fixed frequency of

122 Hz and an adjustable frequency between 15 Hz to once every 16.8 seconds with a

duty cycle that is adjustable from 0 % to 99.6 % that is used to either dim or blink all LEDs

with the same value.

Each LEDn output can be off, on (no PWM control), set at its individual PWM controller

value or at both individual and group PWM controller values. The PCA9952 and PCA9955

operate with a supply voltage range of 3 V to 5.5 V and the constant current sink LEDn

outputs allow up to 40 V for the LED supply. The output peak current is adjustable with an

8-bit linear DAC from 225 A to 57 mA.

These devices have built-in open, short load and overtemperature detection circuitry. The

error information from the corresponding register can be read via the I

a thermal shutdown feature protects the device when internal junction temperature

exceeds the limit allowed for the process.

The PCA9952 and PCA9955 devices have Fast-mode Plus (Fm+) I

devices offer higher frequency (up to 1 MHz) or more densely populated bus operation

(up to 4000 pF).

The PCA9952 is identical to PCA9955 except for the following differences:

The active LOW output enable input pin (OE), available only on PCA9952, blinks all the

LEDn outputs and can be used to externally PWM the outputs, which is useful when

multiple devices need to be dimmed or blinked together without using software control.

Software programmable LED Group and three Sub Call I

defined groups of PCA9952/55 devices to respond to a common I

allowing for example, all red LEDs to be turned on or off at the same time or marquee

chasing effect, thus minimizing I

a unique Sub Call address to identify it as a 16-channel LED driver. This allows mixing of

devices with different channel widths. Four hardware address pins on PCA9955 allow up

to 16 devices on the same bus. In the case of PCA9952, three hardware address pins

allow up to 8 devices on the same bus.

•

PCA9952; PCA9955

16-channel Fm+ I

Rev. 1 — 2 December 2011

The PCA9952 has only 3 hardware address pins compared to 4 on PCA9955.

The PCA9952 has an output enable pin (OE) and the PCA9955 does not.

C-bus 57 mA constant current LED driver

C-bus commands. On power-up, PCA9952/55 will have

C-bus controlled 16-channel constant current LED

C-bus addresses allow all or

C-bus address,

Product data sheet

C-bus interface. Fm+

C-bus. Additionally,

Related parts for pca9952

Related keywords

pca9952 datasheet
pca9952 data sheet
pca9952 pdf datasheet
pca9952 component
pca9952 part
pca9952 distributor
pca9952 RoHS
pca9952 datasheet download