lpc2210fbd144-01 NXP Semiconductors, lpc2210fbd144-01 Datasheet - Page 9

• Manufacturer Part Number: lpc2210fbd144-01
• Description: 16/32-bit Arm Microcontroller With 10-bit Adc And External Memory Interface
• Manufacturer: NXP Semiconductors

NXP Semiconductors
Table 4.
LPC2210_2220_5
Product data sheet
Symbol
P0.13/DTR1/
MAT1.1
P0.14/DCD1/
EINT1
P0.15/RI1/
EINT2
P0.16/EINT0/
MAT0.2/CAP0.2
P0.17/CAP1.2/
SCK1/MAT1.2
P0.18/CAP1.3/
MISO1/MAT1.3
P0.19/MAT1.2/
MOSI1/CAP1.2
P0.20/MAT1.3/
SSEL1/ EINT3
P0.21/PWM5/
CAP1.3
P0.22/CAP0.0/
MAT0.0
P0.23
P0.24
P0.25
P0.27/AIN0/
CAP0.1/MAT0.1
Pin description
Pin (LQFP)
85
92
99
100
101
121
122
123
4
5
6
8
21
23
[1]
[1]
[1]
[1]
[1]
[2]
[2]
[1]
[4]
[2]
[1]
[1]
[1]
[2]
…continued
Pin (TFBGA) Type
H10
G10
E11
E10
D13
D8
C8
B8
C1
D4
D3
D1
H1
H3
[2]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[4]
[2]
[2]
[1]
[1]
[2]
O
O
I
I
I
I
I
O
I
I
I/O
O
I
I/O
O
O
I/O
I
O
I
I
O
I
I
O
I/O
I/O
I/O
I
I
O
Rev. 5 — 20 December 2007
16/32-bit ARM microcontrollers with external memory interface
Description
DTR1 — Data Terminal Ready output for UART1.
MAT1.1 — Match output for Timer 1, channel 1.
DCD1 — Data Carrier Detect input for UART1.
EINT1 — External interrupt 1 input.
Note: LOW on this pin while RESET is LOW forces on-chip
bootloader to take over control of the part after reset.
RI1 — Ring Indicator input for UART1.
EINT2 — External interrupt 2 input.
EINT0 — External interrupt 0 input.
MAT0.2 — Match output for Timer 0, channel 2.
CAP0.2 — Capture input for Timer 0, channel 2.
CAP1.2 — Capture input for Timer 1, channel 2.
SCK1 — Serial Clock for SPI1/SSI/Microwire.
SPI/SSI/Microwire clock output from master or input to slave.
MAT1.2 — Match output for Timer 1, channel 2.
CAP1.3 — Capture input for Timer 1, channel 3.
MISO1 — Master In Slave Out for SPI1. Data input to SPI
master or data output from SPI slave.
MAT1.3 — Match output for Timer 1, channel 3.
MAT1.2 — Match output for Timer 1, channel 2.
MOSI1 — Master Out Slave In for SPI1. Data output from SPI
master or data input to SPI slave.
CAP1.2 — Capture input for Timer 1, channel 2.
MAT1.3 — Match output for Timer 1, channel 3.
SSEL1 — Slave Select for SPI1/Microwire. Used to select the
SPI or Microwire interface as a slave. Frame synchronization
in case of 4-wire SSI.
EINT3 — External interrupt 3 input.
PWM5 — Pulse Width Modulator output 5.
CAP1.3 — Capture input for Timer 1, channel 3.
CAP0.0 — Capture input for Timer 0, channel 0.
MAT0.0 — Match output for Timer 0, channel 0.
General purpose bidirectional digital port only.
General purpose bidirectional digital port only.
General purpose bidirectional digital port only.
AIN0 — ADC, input 0. This analog input is always connected
to its pin.
CAP0.1 — Capture input for Timer 0, channel 1.
MAT0.1 — Match output for Timer 0, channel 1.
•
•
•
SPI interface: MOSI line.
SSI: DX/RX line (SPI1 as a master/slave).
Microwire: SO/SI line (SPI1 as a master/slave).
LPC2210/2220
© NXP B.V. 2007. All rights reserved.
9 of 50