sc16c2550b NXP Semiconductors, sc16c2550b Datasheet - Page 39
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
sc16c2550b
Manufacturer Part Number
sc16c2550b
Description
5 V, 3.3 V And 2.5 V Dual Uart, 5 Mbit/s Max. , With 16-byte Fifos
Manufacturer
NXP Semiconductors
Datasheet
1.SC16C2550B.pdf
(43 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
sc16c2550bIA44
Manufacturer:
EVERLIGHT
Quantity:
99
Part Number:
sc16c2550bIA44
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Company:
Part Number:
sc16c2550bIA44,512
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Company:
Part Number:
sc16c2550bIA44,518
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Company:
Part Number:
sc16c2550bIA44,529
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Company:
Part Number:
sc16c2550bIA44518
Manufacturer:
NXP Semiconductors
Quantity:
135
Part Number:
sc16c2550bIB48
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Company:
Part Number:
sc16c2550bIB48128
Manufacturer:
NXP Semiconductors
Quantity:
1 889
Company:
Part Number:
sc16c2550bIB48151
Manufacturer:
NXP Semiconductors
Quantity:
135
Company:
Part Number:
sc16c2550bIBS,151
Manufacturer:
NXP
Quantity:
1 861
NXP Semiconductors
Table 28.
SC16C2550B_4
Product data sheet
Mounting
Through-hole mount
Through-hole-surface
mount
Suitability of IC packages for wave, reflow and dipping soldering methods
12.3.3 Manual soldering
12.4 Package related soldering information
To overcome these problems the double-wave soldering method was specifically
developed.
If wave soldering is used the following conditions must be observed for optimal results:
During placement and before soldering, the package must be fixed with a droplet of
adhesive. The adhesive can be applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the adhesive is cured.
Typical dwell time of the leads in the wave ranges from 3 seconds to 4 seconds at 250 C
or 265 C, depending on solder material applied, SnPb or Pb-free respectively.
A mildly-activated flux will eliminate the need for removal of corrosive residues in most
applications.
Fix the component by first soldering two diagonally-opposite end leads. Use a low voltage
(24 V or less) soldering iron applied to the flat part of the lead. Contact time must be
limited to 10 seconds at up to 300 C.
When using a dedicated tool, all other leads can be soldered in one operation within
2 seconds to 5 seconds between 270 C and 320 C.
Package
CPGA, HCPGA
DBS, DIP, HDIP, RDBS, SDIP, SIL
PMFP
•
•
•
Use a double-wave soldering method comprising a turbulent wave with high upward
pressure followed by a smooth laminar wave.
For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint longitudinal axis is preferred to be
– smaller than 1.27 mm, the footprint longitudinal axis must be parallel to the
The footprint must incorporate solder thieves at the downstream end.
For packages with leads on four sides, the footprint must be placed at a 45 angle to
the transport direction of the printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
[4]
parallel to the transport direction of the printed-circuit board;
transport direction of the printed-circuit board.
[1]
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
Rev. 04 — 15 February 2007
Soldering method
Wave
suitable
suitable
not suitable
[3]
SC16C2550B
Reflow
not suitable
[2]
© NXP B.V. 2007. All rights reserved.
Dipping
suitable
39 of 43