thncf032mbai TOSHIBA Semiconductor CORPORATION, thncf032mbai Datasheet - Page 8

• Manufacturer Part Number: thncf032mbai
• Description: Thncfxxxmba/bai Series Compactflash Card Flash Technology Based With Interface Flash Memory Card.
• Manufacturer: TOSHIBA Semiconductor CORPORATION

RDY/-BSY
(PC Card Memory Mode)
−
(PC Card I/O Mode)
INTRQ
(True IDE Mode)
−
(PC Card Memory Mode)
−
(PC Card I/O Mode)
−
(True IDE Mode)
RESET
(PC Card Memory Mode)
RESET
(PC Card I/O Mode)
−
(True IDE Mode)
VCC
(PC Card Memory Mode)
(PC Card I/O Mode)
(True IDE Mode)
−
(PC Card Memory Mode)
(PC Card I/O Mode)
(True IDE Mode)
−
(PC Card Memory Mode)
−
(PC Card I/O Mode)
IORDY
(True IDE Mode)
−
(PC Card Memory Mode)
−
(PC Card I/O Mode)
IREQ
REG
REG
REG
RESET
VS1 /
WAIT
WAIT
WE
WE
−
VS2
Signal Name
Dir

O
O
O
I
I
I
Pin No.
Preliminary
13,38
33,40
37
44
41
42
36
In Memory Mode this signal is set high when the CompactFlash
Storage Card is ready to accept a new data transfer operation and
held low when the card is busy .The Host memory card socket
must provide a pull-up resistor.
At power up and at Reset the RDY/
until the CompactFlash Storage Card has completed its power up
or reset function. No access of any type should be made to the
CompactFlash Storage Card during this time .The RDY/-BSY
signal is held high (disabled from being busy) whenever the
following condition is true. The CompactFlash Storage Card has
been powered up with + RESET continuously disconnected or
asserted.
Operation-After the CompactFlash Storage Card has been
configured for I/O operation; this signal is used as interrupt
Request. This line is strobe low to generate a pulse mode interrupt
or held low for a level mode interrupt
In True IDE Mode signal is the active high interrupt Request to the
host.
This signal is used during Memory Cycles to distinguish between
Common Memory and Register (Attribute) Memory accesses. High
for Common Memory, Low for Attribute Memory.
The signal must also be active (low) during I/O Cycles when the I/O
address is on the Bus.
In True IDE Mode this input signal is not used and should be
connected to VCC by the host.
When the pin is high, this signal Resets the CompactFlash Storage
Card. The CompactFlash Storage Card is Reset only at power up if
this pin is left high or open from power-up .The CompactFlash
Storage Card is also Reset when the Soft Reset bit in the Card
Configuration Option Register is set.
In the True IDE Mode this input pin is the active low hardware reset
from the host.
+5V +3.3V power
Voltage
CompactFlash Storage Card CIS can be read at 3.3 volts and
−
The −WAIT signal is driven low by the CompactFlash Storage Card
to signal the host to delay completion of a memory or I/O cycle that
is in progress.
In True IDE Mode this output signal may be used as IORDY
This is a signal driven by the host and used for strobing memory
write data to the registers of the CompactFlash Storage Card when
the card is configured I the memory interface mode. It is also used
for writing the configuration registers.
In PC Card I/O Mode, this signal is used for writing the
configuration registers.
VS2 is reserved by PCMCIA for a secondary voltage.
Sense
Signals.
THNCFxxxMBA/BAI Series
Description
-VS1
−
is
BSY signal is held low (busy)
grounded
2002-10-20 8/48
so
that
the