ne564d NXP Semiconductors, ne564d Datasheet - Page 5
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
ne564d
Manufacturer Part Number
ne564d
Description
Ne564 Phase-locked Loop
Manufacturer
NXP Semiconductors
Datasheet
1.NE564D.pdf
(9 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
NE564D
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Philips Semiconductors
FUNCTIONAL DESCRIPTION
(Figure 6)
The NE564 is a monolithic phase-locked loop with a post detection
processor. The use of Schottky clamped transistors and optimized
device geometries extends the frequency of operation to greater
than 50MHz.
In addition to the classical PLL applications, the NE564 can be used
as a modulator with a controllable frequency deviation.
The output of the PLL can be written as shown in the following
equation:
K
f
f
The process of recovering FSK signals involves the conversion of
the PLL output into logic compatible signals. For high data rates, a
considerable amount of carrier will be present at the output of the
PLL due to the wideband nature of the loop filter. To avoid the use
of complicated filters, a comparator with hysteresis or Schmitt trigger
is required. With the conversion gain of the VCO fixed, the output
voltage as given by Equation 1 varies according to the frequency
deviation of f
is necessary that the hysteresis of the Schmitt trigger be capable of
being changed, so that it can be optimized for a particular system.
This is accomplished in the 564 by varying the voltage at Pin 15
which results in a change of the hysteresis of the Schmitt trigger.
For FSK signals, an important factor to be considered is the drift in
the free-running frequency of the VCO itself. If this changes due to
temperature, according to Equation 1 it will lead to a change in the
DC levels of the PLL output, and consequently to errors in the digital
output signal. This is especially true for narrowband signals where
the deviation in f
temperature. This effect can be eliminated if the DC or average
value of the signal is retrieved and used as the reference to the
comparator. In this manner, variations in the DC levels of the PLL
output do not affect the FSK output.
VCO Section
Due to its inherent high-frequency performance, an emitter-coupled
oscillator is used in the VCO. In the circuit, shown in the equivalent
schematic, transistors Q21 and Q23 with current sources Q25 - Q26
form the basic oscillator. The approximate free-running frequency of
the oscillator is shown in the following equation:
R
C
C
Variation of V
frequency of the oscillator. As indicated by Equation 2, the
frequency of the oscillator has a negative temperature coefficient
due to the monolithic resistor. To compensate for this, a current I
with negative temperature coefficient is introduced to achieve a low
frequency drift with temperature.
1994 Aug 31
V
f
IN
O
O
VCO
C
1
S
O
= free-running frequency of the VCO
Phase-locked loop
= frequency of the input signal
= external frequency setting capacitor
= R
= stray capacitance
=
= conversion gain of the VCO
22 R
(f
19
IN
K
VCO
= R
- f
C
O
IN
(C
20
D
1
)
from f
1
(phase detector output voltage) changes the
= 100 (INTERNAL)
IN
+ C
itself may be less than the change in f
S
O
)
. Since this differs from system to system, it
O
due to
(1)
(2)
R
5
Phase Comparator Section
The phase detection processor consists of a doubled-balanced
modulator with a limiter amplifier to improve AM rejection.
Schottky-clamped vertical PNPs are used to obtain TTL level inputs.
The loop gain can be varied by changing the current in Q
which effectively changes the gain of the differential amplifiers. This
can be accomplished by introducing a current at Pin 2.
Post Detection Processor Section
The post detection processor consists of a unity gain
transconductance amplifier and comparator. The amplifier can be
used as a DC retriever for demodulation of FSK signals, and as a
post detection filter for linear FM demodulation. The comparator has
adjustable hysteresis so that phase jitter in the output signal can be
eliminated.
As shown in the equivalent schematic, the DC retriever is formed by
the transconductance amplifier Q
capacitor which is connected at the amplifier output (Pin 14). This
forms an integrator whose output voltage is shown in the following
equation:
g
C
V
With proper selection of C
varied so that the output voltage is the DC or average value of the
input signal for use in FSK, or as a post detection filter in linear
demodulation.
The comparator with hysteresis is made up of Q
positive feedback being provided by Q
varied by changing the current in Q
loop gain of the comparator. This method of hysteresis control,
which is a DC control, provides symmetric variation around the
nominal value.
Design Formula
The free-running frequency of the VCO is shown by the following
equation:
R
C
C
The loop filter diagram shown is explained by the following equation:
R = R
By adding capacitors to Pins 4 and 5, a pole is added to the loop
transfer at
f
f
V
O
S
M
IN
2
C
1
S
O
=
=
= capacitor at the output (Pin 14)
= external cap in farads
= transconductance of the amplifier
= 100
= stray capacitance
=
= signal voltage at amplifier input
1 + sRC
12
22 R
g
C
RC
M
= R
2
1
1
C
3
13
(C
V
1
3
IN
= 1.3k (Internal)*
1
(First Order)
dt
+ C
S
)
2
*Refer to Figure 6.
, the integrator time constant can be
NOTE:
42
52
- Q
with a resulting variation in the
47
43
- Q
together with an external
48
. The hysteresis is
NE/SE564
Product specification
49
- Q
50
with
4
and Q
(3)
(4)
(5)
15