S29CD016G SPANSION, S29CD016G Datasheet - Page 86

• Manufacturer Part Number: S29CD016G
• Description: 16 Megabit (512 K x 32-Bit) CMOS 2.5 Volt-only Burst Mode / Dual Boot / Simultaneous Read/Write Flash Memory
• Manufacturer: SPANSION

Physical Dimensions
PRQ080–80-Lead Plastic Quad Flat Package
86
PIN P
PIN S
PACKAGE
JEDEC
SYMBOL
-A-
A1
A
A1
A2
b
c
D
D1
D3
e
E
E1
E3
aaa
ccc
L
P
Q
R
S
A2
17.00
13.90
23.00
19.90
SEE NOTE 3
MIN
0.25
2.70
0.30
0.15
0.73
---
--
--
--
--
PIN ONE I.D.
SEE DETAIL X
MO-108(B)CB-1
PQR 080
17.20
14.00
23.20
20.00
18.40
NOM
2.80
12.0
0.80
0.20
0.10
0.88
24
40
64
80
--
--
--
--
6
3
D1
D3
D
e BASIC
-D-
17.40
14.10
23.40
20.10
MAX
3.35
2.90
0.45
0.23
1.03
---
--
--
--
--
NOTES
SEE NOTE 4
SEE NOTE 3
REFERENCE
BASIC, SEE NOTE 7
SEE NOTE 3
REFERENCE
PIN Q
S
A d v a n c e
S
-B-
A
E3
PIN R
-A-
-C-
S29CD016G
E1
2
3
E
SEATING PLANE
6
0.30 ± 0.05 R
PLANE
GAGE
NOTES:
1.
2.
3.
4.
5.
6.
7.
8.
9.
I n f o r m a t i o n
ALL DIMENSIONS AND TOLERANCES CONFORM TO
ANSI Y14.5M-1982.
DATUM PLANE -A- IS LOCATED AT THE MOLD PARTING LINE
AND IS COINCIDENT WITH THE BOTTOM OF THE LEAD WHERE
THE LEAD EXITS THE PLASTIC BODY.
DIMENSIONS "D1" AND "E1" DO NOT INCLUD MOLD PROTRUSION.
ALLOWABLE PROTRUSION IS 0.25 mm PER SIDE.
DIMENSIONS "D1" AND "E1" INCLUDE MOLD MISMATCH AND
ARE DETERMINED AT DATUM PLANE -A-
DIMENSION "B" DOES NOT INCLUDE DAMBAR PROTRUSION.
CONTROLLING DIMENSIONS: MILLIMETER.
DIMENSIONS "D" AND "E" ARE MEASURED FROM BOTH
INNERMOST AND OUTERMOST POINTS.
DEVIATION FROM LEAD-TIP TRUE POSITION SHALL BE WITHIN
±0.0076 mm FOR PITCH > 0.5 mm AND WITHIN ±0.04 FOR
PITCH < 0.5 mm.
LEAD COPLANARITY SHALL BE WITHIN: (REFER TO 06-500)
1 - 0.10 mm FOR DEVICES WITH LEAD PITCH OF 0.65 - 0.80 mm
2 - 0.076 mm FOR DEVICES WITH LEAD PITCH OF 0.50 mm.
COPLANARITY IS MEASURED PER SPECIFICATION 06-500.
HALF SPAN (CENTER OF PACKAGE TO LEAD TIP) SHALL BE
WITHIN ±0.0085".
0.25
0˚MIN.
SECTION S-S
L
b
0˚-7˚
0.20 MIN. FLAT SHOULDER
c
TYP.
TYP.
DETAIL X
7˚
7˚
a
a
a
M
C A B
S29CD016_00_A4 November 5, 2004
b
S D S
A
4
ccc
3213\38.4C
C