ADT7476ARQH ONSEMI [ON Semiconductor], ADT7476ARQH Datasheet - Page 55
ADT7476ARQH
Manufacturer Part Number
ADT7476ARQH
Description
dBCOOL Remote Thermal Controller and Voltage Monitor
Manufacturer
ONSEMI [ON Semiconductor]
Datasheet
1.ADT7476ARQH.pdf
(67 pages)
- Current page: 55 of 67
- Download datasheet (621Kb)
1. These registers become read−only when the Configuration Register 1 lock bit is set to 1. Any subsequent attempts to write to these registers fail.
Table 30. PWM Configuration Registers
Bit No.
[2:0]
[7:5]
Register Address
[3]
[4]
0x5C
0x5D
0x5E
Name
BHVR
SPIN
RES
INV
R/W (Note 1)
R/W
R/W
R/W
R/W
R/W
R/W
R/W
N/A
These bits control the startup timeout for PWMx. The PWM output stays high until two valid
TACH rising edges are seen from the fan. If there is not a valid TACH signal during the fan
TACH measurement directly after the fan startup timeout period, the TACH measurement
reads 0xFFFF and Interrupt Status Register 2 reflects the fan fault. If the TACH minimum
high and low bytes contain 0xFFFF or 0x0000, the Interrupt Status Register 2 bit is not set,
even if the fan has not started.
000 = No startup timeout
001 = 100 ms
010 = 250 ms (default)
011 = 400 ms
100 = 667 ms
101 = 1 sec
110 = 2 sec
111 = 4 sec
Reserved. Do not write to this bit.
This bit inverts the PWM output. The default is 0, which corresponds to a logic high output for
100% duty cycle. Setting this bit to 1 inverts the PWM output, so 100% duty cycle
corresponds to a logic low output.
These bits assign each fan to a particular temperature sensor for localized cooling.
000 = Remote 1 temperature controls PWMx (automatic fan control mode).
001 = Local temperature controls PWMx (automatic fan control mode).
010 = Remote 2 temperature controls PWMx (automatic fan control mode).
011 = PWMx runs full speed (default).
100 = PWMx disabled.
101 = Fastest speed calculated by local and Remote 2 temperature controls PWMx.
110 = Fastest speed calculated by all three temperature channel controls PWMx.
111 = Manual mode. PWM current duty cycle registers (0x30 to 0x32) become writable.
http://onsemi.com
PWM1 configuration
PWM2 configuration
PWM3 configuration
Description
55
Description
Power−On Default
0x62
0x62
0x62
Related parts for ADT7476ARQH
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
300 Watt, SOT-23 Low Capacitance TVS for High Speed Line Protections
Manufacturer:
ONSEMI [ON Semiconductor]
Datasheet:
Part Number:
Description:
SWITCHMODE Power Rectifier
Manufacturer:
ONSEMI [ON Semiconductor]
Datasheet:
Part Number:
Description:
TMOS E−FET Power Field Effect Transistor DPAK for Surface Mount
Manufacturer:
ONSEMI [ON Semiconductor]
Datasheet:
Part Number:
Description:
Trench Power MOSFET -20 V, Single P-Channel, SOT-23
Manufacturer:
ONSEMI [ON Semiconductor]
Datasheet:
Part Number:
Description:
Power MOSFET 12 A, 60 V
Manufacturer:
ONSEMI [ON Semiconductor]
Datasheet:
Part Number:
Description:
Power MOSFET
Manufacturer:
ONSEMI [ON Semiconductor]
Datasheet:
Part Number:
Description:
Power MOSFET
Manufacturer:
ONSEMI [ON Semiconductor]
Datasheet:
Part Number:
Description:
Power MOSFET 3.0 Amps 60 Volts N−Channel
Manufacturer:
ONSEMI [ON Semiconductor]
Datasheet:
Part Number:
Description:
Power MOSFET 2.0 A, 60 V, Logic Level
Manufacturer:
ONSEMI [ON Semiconductor]
Datasheet:
Part Number:
Description:
Power MOSFET 2 Amps, 500 Volts P−Channel D2PAK
Manufacturer:
ONSEMI [ON Semiconductor]
Datasheet:
Part Number:
Description:
Power MOSFET 23 Amps, 25 Volts N−Channel D2PAK
Manufacturer:
ONSEMI [ON Semiconductor]
Datasheet:
Part Number:
Description:
Power MOSFET -60 V, -27.5 A, P-Channel D2PAK
Manufacturer:
ONSEMI [ON Semiconductor]
Datasheet:
Part Number:
Description:
Power MOSFET 30 Amps, 200 Volts N−Channel Enhancement−Mode D2PAK
Manufacturer:
ONSEMI [ON Semiconductor]
Datasheet:
Part Number:
Description:
N-Channel Enhancement−Mode D2PAK
Manufacturer:
ONSEMI [ON Semiconductor]
Datasheet:
Part Number:
Description:
60 V, 60 A, N-Channel TO-220 and D2PAK
Manufacturer:
ONSEMI [ON Semiconductor]
Datasheet: