LM3S101-CRN20-XNPP ETC1 [List of Unclassifed Manufacturers], LM3S101-CRN20-XNPP Datasheet - Page 225
LM3S101-CRN20-XNPP
Manufacturer Part Number
LM3S101-CRN20-XNPP
Description
Microcontroller
Manufacturer
ETC1 [List of Unclassifed Manufacturers]
Datasheet
1.LM3S101-CRN20-XNPP.pdf
(284 pages)
- Current page: 225 of 284
- Download datasheet (3Mb)
Synchronous Serial Interface (SSI)
12.2.4.7
225
In this configuration, during idle periods:
If the SSI is enabled and there is valid data within the transmit FIFO, the start of transmission is
signified by the SSIFss master signal being driven Low. The master SSITx output pad is enabled.
After a further one-half SSIClk period, both master and slave data are enabled onto their
respective transmission lines. At the same time, SSIClk is enabled with a falling edge transition.
Data is then captured on the rising edges and propagated on the falling edges of the SSIClk
signal.
After all bits have been transferred, in the case of a single word transmission, the SSIFss line is
returned to its idle high state one SSIClk period after the last bit has been captured.
For continuous back-to-back transmissions, the SSIFss pin remains in its active Low state, until
the final bit of the last word has been captured, and then returns to its idle state as described
above.
For continuous back-to-back transfers, the SSIFss pin is held Low between successive data
words and termination is the same as that of the single word transfer.
National Semiconductor MICROWIRE Frame Format
Figure 12-10 shows the National Semiconductor MICROWIRE frame format, again for a single
frame. Figure 12-11 shows the same format when back-to-back frames are transmitted.
Figure 12-10. National Semiconductor MICROWIRE Frame Format (Single Frame)
MICROWIRE format is very similar to SPI format, except that transmission is half-duplex instead
of full-duplex, using a master-slave message passing technique. Each serial transmission begins
with an 8-bit control word that is transmitted from the SSI to the off-chip slave device. During this
transmission, no incoming data is received by the SSI. After the message has been sent, the off-
chip slave decodes it and, after waiting one serial clock after the last bit of the 8-bit control
message has been sent, responds with the required data. The returned data is 4 to 16 bits in
length, making the total frame length anywhere from 13 to 25 bits.
In this configuration, during idle periods:
SSIClk is forced High
SSIFss is forced High
The transmit data line SSITx is arbitrarily forced Low
When the SSI is configured as a master, it enables the SSIClk pad
When the SSI is configured as a slave, it disables the SSIClk pad
SSIClk is forced Low
SSIFss is forced High
The transmit data line SSITx is arbitrarily forced Low
SSIClk
SSIFss
SSIRx
SSITx
MSB
8-bit control
Preliminary
LSB
0
MSB
output data
4 to 16 bits
LSB
March 22, 2006
Related parts for LM3S101-CRN20-XNPP
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Microcontroller
Manufacturer:
Luminary Micro, Inc.
Datasheet:
Part Number:
Description:
Microcontroller
Manufacturer:
Luminary Micro, Inc.
Datasheet:
Part Number:
Description:
Microcontroller
Manufacturer:
ETC2 [List of Unclassifed Manufacturers]
Datasheet:
Part Number:
Description:
14-Bit, 1 GSPS Digital-to-Analog Converter with Standby Mode of Operation
Manufacturer:
ETC1 [List of Unclassifed Manufacturers]
Datasheet:
Part Number:
Description:
A SERIES OF SPECTRAL - RESPONSE SILICON PHOTOCELLS DESIGNED FOR UNIQUE PRODUCT APPLICATIONS
Manufacturer:
ETC1 [List of Unclassifed Manufacturers]
Datasheet:
Part Number:
Description:
Mini size of Discrete semiconductor elements
Manufacturer:
ETC1 [List of Unclassifed Manufacturers]
Datasheet:
Part Number:
Description:
3 Watts of Output Power From a Package
Manufacturer:
ETC1 [List of Unclassifed Manufacturers]
Datasheet:
Part Number:
Description:
DTMF Tone Generator
Manufacturer:
ETC1 [List of Unclassifed Manufacturers]
Datasheet:
Part Number:
Description:
SILICON TRIACS
Manufacturer:
ETC1 [List of Unclassifed Manufacturers]
Datasheet:
Part Number:
Description:
N P-Channel Enhancement Mode Enhancement Mode
Manufacturer:
ETC1 [List of Unclassifed Manufacturers]
Datasheet:
Part Number:
Description:
Dot Matrix LCD 80-Channel Driver
Manufacturer:
ETC1 [List of Unclassifed Manufacturers]
Datasheet:
Part Number:
Description:
Level shifting hot swappable I2C-bus and SMBus bus buffer
Manufacturer:
ETC1 [List of Unclassifed Manufacturers]
Datasheet:
Part Number:
Description:
Common Mode Choke Coils for Signal Line SMD
Manufacturer:
ETC1 [List of Unclassifed Manufacturers]
Datasheet:
Part Number:
Description:
Technische Daten Technical Data
Manufacturer:
ETC1 [List of Unclassifed Manufacturers]
Datasheet:
Part Number:
Description:
2-Channel PWM Controller for LCD Bias
Manufacturer:
ETC1 [List of Unclassifed Manufacturers]
Datasheet: