GAL16LV8C-15LJ LATTICE [Lattice Semiconductor], GAL16LV8C-15LJ Datasheet - Page 17
![no-image](/images/no-image-200.jpg)
GAL16LV8C-15LJ
Manufacturer Part Number
GAL16LV8C-15LJ
Description
Low Voltage E2CMOS PLD Generic Array Logic
Manufacturer
LATTICE [Lattice Semiconductor]
Datasheet
1.GAL16LV8C-15LJ.pdf
(22 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
GAL16LV8C-15LJ
Manufacturer:
LAT
Quantity:
2 700
Company:
Part Number:
GAL16LV8C-15LJ
Manufacturer:
LAT
Quantity:
2 700
Part Number:
GAL16LV8C-15LJ
Manufacturer:
LATTICE
Quantity:
20 000
Company:
Part Number:
GAL16LV8C-15LJN
Manufacturer:
LAT
Quantity:
4 400
Company:
Part Number:
GAL16LV8C-15LJN
Manufacturer:
LAT
Quantity:
4 400
Company:
Part Number:
GAL16LV8C-15LJN
Manufacturer:
Lattice
Quantity:
135
Company:
Part Number:
GAL16LV8C-15LJN
Manufacturer:
Lattice Semiconductor Corporation
Quantity:
10 000
Part Number:
GAL16LV8C-15LJN
Manufacturer:
LATTIC
Quantity:
20 000
An electronic signature is provided in every GAL16LV8 device. It
contains 64 bits of reprogrammable memory that can contain user
defined data. Some uses include user ID codes, revision numbers,
or inventory control. The signature data is always available to the
user independent of the state of the security cell.
NOTE: The electronic signature is included in checksum calcula-
tions. Changing the electronic signature will alter the checksum.
A security cell is provided in the GAL16LV8 devices to prevent un-
authorized copying of the array patterns. Once programmed, this
cell prevents further read access to the functional bits in the device.
This cell can only be erased by re-programming the device, so the
original configuration can never be examined once this cell is pro-
grammed. The Electronic Signature is always available to the user,
regardless of the state of this control cell.
GAL16LV8 devices are designed with an on-board charge pump
to negatively bias the substrate. The negative bias minimizes the
potential of latch-up caused by negative input undershoots.
GAL devices are programmed using a Lattice Semiconductor-ap-
proved Logic Programmer, available from a number of manufac-
turers. Complete programming of the device takes only a few sec-
onds. Erasing of the device is transparent to the user, and is done
automatically as part of the programming cycle.
Electronic Signature
Security Cell
Latch-Up Protection
Device Programming
17
When testing state machine designs, all possible states and state
transitions must be verified in the design, not just those required
in the normal machine operations. This is because, in system
operation, certain events occur that may throw the logic into an
illegal state (power-up, line voltage glitches, brown-outs, etc.). To
test a design for proper treatment of these conditions, a way must
be provided to break the feedback paths, and force any desired (i.e.,
illegal) state into the registers. Then the machine can be sequenced
and the outputs tested for correct next state conditions.
GAL16LV8 devices include circuitry that allows each registered
output to be synchronously set either high or low. Thus, any present
state condition can be forced for test sequencing. If necessary,
approved GAL programmers capable of executing text vectors
perform output register preload automatically.
GAL16LV8 devices are designed with TTL level compatible input
buffers. These buffers have a characteristically high impedance,
and present a much lighter load to the driving logic than bipolar TTL
devices.
The GAL16LV8D input and I/O pins have built-in active pull-ups.
As a result, unused inputs and I/O's will float to a TTL "high" (logical
"1"). Lattice Semiconductor recommends that all unused inputs
and tri-stated I/O pins be connected to another active input, V
or Ground. Doing this will tend to improve noise immunity and re-
duce I
Output Register Preload
Input Buffers
Typical Input Pull-up Characteristic (GAL16LV8D)
CC
-10
-20
-30
-40
-50
-60
-70
-80
0
for the device.
Specifications GAL16LV8
Input Voltage (V)
CC
,