HI-303 Intersil Corporation, HI-303 Datasheet
HI-303
Related parts for HI-303
HI-303 Summary of contents
Page 1
... Break-Before-Make Delay . . . . . . . . . . . . . . . . . . . . 60ns • Charge Injection . . . . . . . . . . . . . . . . . . . . . . . . . . . 30pC • TTL, CMOS Compatible • Symmetrical Switch Elements • Low Operating Power (Typ for Hl-301 and HI-303 1.0mW Applications • Sample and Hold (i.e., Low Leakage Switching) • Op Amp Gain Switching (i.e., Low On Resistance) PKG. NO. ...
Page 2
... IN D1A MN1A GND V- 2 HI-301 thru HI-307 SWITCH CELL V+ MN1B MN2B MN3B MP5B MP4B MN4B MP3B MP2B MP1B DIGITAL INPUT BUFFER AND LEVEL SHIFTER MP2A MP3A MP4A MN2A MN3A MN4A OUT MN6B V- MP5A MP6A MP7A MP8A MN5A MN6A MN7A MN8A SWITCH CELL DRIVER ...
Page 3
... Maximum Lead Temperature (Soldering 10s 300 (SOIC - Lead Tips Only 125 Logic Input. HI-301 and HI-303 for Logic “1” = 11V, for Logic “0” = 3.5V, Unless Otherwise Specifi TEMP MIN TYP 25 - 210 ...
Page 4
... To drive from DTL/TTL circuits, pullup resistors to +5V supply are recommended. 13. HI-301 thru HI-303 only. 14. HI-307 only. 4 HI-301 thru HI-307 = Logic Input. HI-301 and HI-303 for Logic “1” = 11V, for Logic “0” = 3.5V, Unless Otherwise Specified (Continued) IN TEMP ...
Page 5
... HI-307 1.2 1.6 LOGIC “1” = SWITCH ON V LOGIC INH INPUT 50% 50 90% 10 OFF SWITCH OUTPUT t ON FIGURE 1B. MEASUREMENT POINTS OFF 6 HI-301 AND HI-303 LOGIC INPUT 0 0.4 0.8 1.2 TIME ( s) FIGURE 2B. TTL LOGIC INPUT 10 (NOTE 16 10V GEN 0 0 0.4 0.8 1.2 TIME ( s) FIGURE 2D 10V ANALOG 1 ...
Page 6
... FIGURE 2. SWITCHING WAVEFORMS FOR VARIOUS ANALOG INPUT VOLTAGES 15V + + LOGIC INPUT V- GND -15V SWITCH TYPE HI-301, HI-303 HI-307 FIGURE 3A. TEST CIRCUIT 6 HI-301 thru HI-307 (Continued) 1.2 1 1.2 1.6 = -5V OUT 1 LOGIC OUT 2 INPUT SWITCH V OUTPUTS ...
Page 7
... DRAIN VOLTAGE (V) FIGURE DS(ON) 100 V+ = +15V -15V 15V HI-301 AND HI-303 1.0 HI-307 0 100 1K LOGIC SWITCHING FREQUENCY (50% DUTY CYCLE) (Hz) FIGURE 6. DEVICE POWER DISSIPATION vs SWITCHING FREQUENCY (SINGLE LOGIC INPUT) 10 +15V -15V 1.0 0.1 0. TEMPERATURE ( FIGURE 8. I ...
Page 8
... TEMPERATURE ( FIGURE 12. SWITCHING TIME vs TEMPERATURE, HI-301 AND HI-303 300 200 OFF 100 0 5 NEGATIVE SUPPLY (V) FIGURE 14. SWITCHING TIME vs NEGATIVE SUPPLY VOLTAGE, HI-301 AND HI-303 8 HI-301 thru HI-307 (Continued FIGURE 11. DIGITAL INPUT CAPACITANCE vs INPUT VOLTAGE 300 200 100 65 85 ...
Page 9
... Typical Performance Curves 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 t OFF t OPEN 0.2 HI-301/303 ONLY POSITIVE SUPPLY VOLTAGE (V) FIGURE 16. SWITCHING TIME AND BREAK-BEFORE-MAKE TIME vs POSITIVE SUPPLY VOLTAGE, HI-301 AND HI-303 FIGURE 18. INPUT SWITCHING THRESHOLD vs POSITIVE SUPPLY VOLTAGE 9 HI-301 thru HI-307 (Continued) 1 -15V 1 4.0V INH INL 1.4 1.2 1.0 0.8 ...
Page 10
... S NOTES: 1. Index area: A notch or a pin one identification mark shall be locat- ed adjacent to pin one and shall be located within the shaded area shown. The manufacturer’s identification shall not be used as a pin one identification mark. 2. The maximum limits of lead dimensions b and shall be measured at the centroid of the finished lead surfaces, when solder dip or tin plate lead finish is applied ...
Page 11
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...