HY27SF161G2A HYNIX [Hynix Semiconductor], HY27SF161G2A Datasheet
HY27SF161G2A
Related parts for HY27SF161G2A
HY27SF161G2A Summary of contents
Page 1
... NAND FLASH This document is a general product description and is subject to change without notice. Hynix does not assume any responsibility for use of circuits described. No patent licenses are implied. Rev 0.3 / Nov. 2006 1Gbit (128Mx8bit / 64Mx16bit) NAND Flash HY27SF081G2A HY27SF161G2A HY27SF(08/16)1G2A Series 1 ...
Page 2
Document Title 1Gbit (128Mx8bit / 64Mx16bit) NAND Flash Memory Revision History Revision No. 0.01 Initial Draft. 1) Change AC Conditions table 2) Change DC and Operating Characteristics Test Conditions ( Before CE= After CE= 0.1 Typ ( Before After 3) ...
Page 3
... Bytes x 64 Pages x 1,024 Blocks = (1K+32) Words x 64 Pages x 1,024 Blocks PAGE SIZE - x8 device : (2K+64 spare) Bytes : HY27SF081G2A - x16 device : (1K+32 spare) Words : HY27SF161G2A BLOCK SIZE - x8 device: (128K + 4K spare) Bytes - x16 device: (64K + 2K spare) Words PAGE READ / PROGRAM - Random access: 25us (max.) - Sequential access: 50ns (min.) - Page program time: 200us (typ ...
Page 4
... The HYNIX HY27SF(08/16)1G2A series is available TSOP1 mm USOP mm, FBGA mm. 1.1 Product List PART NUMBER HY27SF081G2A HY27SF161G2A Rev 0.3 / Nov. 2006 1Gbit (128Mx8bit / 64Mx16bit) NAND Flash ORIZATION VCC RANGE x8 1.7V - 1.95 Volt ...
Page 5
IO15 - IO8 IO7 - IO0 CLE ALE R/B Vcc Vss NC Rev 0.3 / Nov. 2006 1Gbit (128Mx8bit / 64Mx16bit) NAND Flash Figure1: Logic Diagram Data Inputs / Outputs (x16 Only) Data Inputs / Outputs ...
Page 6
Figure 2. 48TSOP1 Contactions, x8 and x16 Device Rev 0.3 / Nov. 2006 1Gbit (128Mx8bit / 64Mx16bit) NAND Flash Figure 3. 48USOP1 Contactions, x8 HY27SF(08/16)1G2A Series 6 ...
Page 7
Figure 4. 63FBGA Contactions, x8 Device (Top view through package) Rev 0.3 / Nov. 2006 HY27SF(08/16)1G2A Series 1Gbit (128Mx8bit / 64Mx16bit) NAND Flash 7 ...
Page 8
PIN DESCRIPTION Pin Name DATA INPUTS/OUTPUTS IO0-IO7 The IO pins allow to input command, address and data and to output data during read / program IO8-IO15(1) operations. The inputs are latched on the rising edge of Write Enable (WE). ...
Page 9
IO0 1st Cycle A0 2nd Cycle A8 3rd Cycle A12 4th Cycle A20 NOTE must be set to Low. IO0 1st Cycle A0 2nd Cycle A8 3rd Cycle A11 4th Cycle A19 NOTE must be set ...
Page 10
CLE ALE ( NOTE: 1. With ...
Page 11
BUS OPERATION There are six standard bus operations that control the device. These are Command Input, Address Input, Data Input, Data Output, Write Protect, and Standby. Typically glitches less than Chip Enable, Write Enable and Read ...
Page 12
DEVICE OPERATION 3.1 Page Read. Upon initial device power up, the device defaults to Read mode. This operation is also initiated by writing 00h and 30h to the command register along with four address cycles. In two consecutive read ...
Page 13
Block Erase. The Erase operation is done on a block basis. Block address loading is accomplished in two cycles initiated by an Erase Setup command (60h). Only address A18 to A27 (X8) or A17 to A26 (X16) is valid ...
Page 14
Read Status Register. The device contains a Status Register which may be read to find out whether read, program or erase operation is com- pleted, and whether the program or erase operation is completed successfully. After writing 70h command ...
Page 15
Cache program Cache Program is an extension of Page Program, which is executed with 2112byte (X8 device) or 1056word (X16 device) data registers, and is available only within a block. Since the device has 1 page of cache memory, ...
Page 16
Cache Read Cache read operation allows automatic download of consecutive pages the whole device. Immediately after 1st latency end, while user can start reading out data, device internally starts reading following page. Start address of 1st page ...
Page 17
OTHER FEATURES 4.1 Data Protection for Power on/off Sequence The device is designed to offer protection from any involuntary program/erase during power-transitions. An internal voltage detector disables all functions whenever Vcc is below about 1.1V (1.8V version). WP pin ...
Page 18
Parameter Symbol Valid Block Number NOTE: 1. The 1st block is guaranteed valid block cycles with ECC. (1bit/528bytes) Symbol Ambient Operating Temperature (Temperature Range Option Ambient Operating Temperature (Industrial Temperature Range) ...
Page 19
Rev 0.3 / Nov. 2006 HY27SF(08/16)1G2A Series 1Gbit (128Mx8bit / 64Mx16bit) NAND Flash Figure 5 : Block Diagram 19 ...
Page 20
Parameter Sequential Read Operating Current Program Erase Stand-by Current (TTL) Stand-by Current (CMOS) Input Leakage Current Output Leakage Current Input High Voltage Input Low Voltage Output High Voltage Level Output Low Voltage Leve Output Low Current (R/B) Table 9: DC ...
Page 21
Item Input / Output Capacitance Input Capacitance Table 11: Pin Capacitance (TA=25C, F=1.0MHz) Parameter Program Time Dummy Busy Time for Cache Program Dummy Busy Time for Cache Read Number of partial Program Cycles in the same page Block Erase Time ...
Page 22
Parameter CLE Setup time CLE Hold time CE setup time CE hold time WE pulse width ALE setup time ALE hold time Address to Data Loading Data setup time Data hold time Write Cycle time WE High hold time Data ...
Page 23
... Ready/Busy Ready/Busy 6 Ready/Busy Ready/Busy 7 Write Protect Write Protect DEVIIDENTIFIER CYCLE 1st 2nd 3rd 4th Part Number Voltage Bus Width HY27SF081G2A 1.8V HY27SF161G2A 1.8V Rev 0.3 / Nov. 2006 1Gbit (128Mx8bit / 64Mx16bit) NAND Flash Cache Read Program Pass / Fail (N) NA Pass / Fail (N- P/E/R Ready/Busy ...
Page 24
Description 1 2 Die / Package 4 Reserved Single Level 2x Multi-level String Type Reserved Reservedl 1 Number of 2 Simultaneously 3 Programmed Pages 4 Interleave Program Not Support Between different dice Support Not Support Write Cache Support Table 17: ...
Page 25
Rev 0.3 / Nov. 2006 1Gbit (128Mx8bit / 64Mx16bit) NAND Flash Figure 6: Command Latch Cycle Figure 7: Address Latch Cycle HY27SF(08/16)1G2A Series 25 ...
Page 26
I/Ox t R/B Notes : Transition is measured ±200mV from steady state voltage with load. This parameter is sampled and not 100% tested. Figure 9: Sequential Out Cycle after Read (CLE=L, WE=H, ALE=L) Rev 0.3 / Nov. ...
Page 27
CLE I/O x Figure 11: Read Operation (Read One Page) Rev 0.3 / Nov. 2006 1Gbit (128Mx8bit / 64Mx16bit) NAND Flash t CLR t CLS t CLH WHR t DH ...
Page 28
Figure 12: Read Operation intercepted by CE Rev 0.3 / Nov. 2006 HY27SF(08/16)1G2A Series 1Gbit (128Mx8bit / 64Mx16bit) NAND Flash 28 ...
Page 29
Rev 0.3 / Nov. 2006 1Gbit (128Mx8bit / 64Mx16bit) NAND Flash Figure 13 : Random Data output HY27SF(08/16)1G2A Series 29 ...
Page 30
Rev 0.3 / Nov. 2006 1Gbit (128Mx8bit / 64Mx16bit) NAND Flash Figure 14: Page Program Operation HY27SF(08/16)1G2A Series 30 ...
Page 31
Rev 0.3 / Nov. 2006 1Gbit (128Mx8bit / 64Mx16bit) NAND Flash Figure 15 : Random Data In HY27SF(08/16)1G2A Series 31 ...
Page 32
Rev 0.3 / Nov. 2006 1Gbit (128Mx8bit / 64Mx16bit) NAND Flash Figure 16 : Copy Back Program HY27SF(08/16)1G2A Series 32 ...
Page 33
Rev 0.3 / Nov. 2006 HY27SF(08/16)1G2A Series 1Gbit (128Mx8bit / 64Mx16bit) NAND Flash Figure 17 : Cache Program 33 ...
Page 34
Figure 18: Block Erase Operation (Erase One Block) Rev 0.3 / Nov. 2006 1Gbit (128Mx8bit / 64Mx16bit) NAND Flash Figure 19: Read ID Operation HY27SF(08/16)1G2A Series 34 ...
Page 35
Figure 20: start address at page start :after 1st latency uninterrupted data flow Figure 21: exit from cache read in 5us when device internally is reading Rev 0.3 / Nov. 2006 HY27SF(08/16)1G2A Series 1Gbit (128Mx8bit / 64Mx16bit) NAND Flash 35 ...
Page 36
System Interface Using CE don’t care To simplify system interface, CE may be deasserted during data loading or sequential data-reading as shown below. So possible to connect NAND Flash to a microporcessor. The only function that was removed ...
Page 37
Figure 25: Power On and Data Protection Timing Rev 0.3 / Nov. 2006 1Gbit (128Mx8bit / 64Mx16bit) NAND Flash Figure 24: Reset Operation VTH = 1.5 Volt for 1.8 Volt Supply devices HY27SF(08/16)1G2A Series 37 ...
Page 38
Figure 26: Ready/Busy Pin electrical specifications Rev 0.3 / Nov. 2006 HY27SF(08/16)1G2A Series 1Gbit (128Mx8bit / 64Mx16bit) NAND Flash 38 ...
Page 39
Bad Block Management Devices with Bad Blocks have the same quality level and the same AC and DC characteristics as devices where all the blocks are valid. A Bad Block does not affect the performance of valid blocks because it ...
Page 40
Write Protect Operation The Erase and Program Operations are automatically reset when WP goes Low (tWW = 100ns, min). The operations are enabled and disabled as follows (Figure 28~31) Rev 0.3 / Nov. 2006 1Gbit (128Mx8bit / 64Mx16bit) NAND Flash ...
Page 41
Rev 0.3 / Nov. 2006 HY27SF(08/16)1G2A Series 1Gbit (128Mx8bit / 64Mx16bit) NAND Flash Figure 30: Enable Erasing Figure 31: Disable Erasing 41 ...
Page 42
Figure 32: 48pin-TSOP1 20mm, Package Outline Symbol alpha Table 20: 48pin-TSOP1 20mm, Package Mechanical Data Rev 0.3 / Nov. 2006 1Gbit (128Mx8bit / 64Mx16bit) NAND ...
Page 43
Figure 33. 48pin-USOP1 17mm, Package Outline Symbol alpha Table 21: 48pin-USOP1 17mm, Package Mechanical Data Rev 0.3 / Nov. 2006 HY27SF(08/16)1G2A Series 1Gbit (128Mx8bit / ...
Page 44
Figure 34. 63-ball FBGA - ball array 0.8mm pitch, Pakage Outline NOTE: Drawing is not to scale. Symbol FD1 FE FE1 SD SE Table 22: ...
Page 45
MARKING INFORMATION - ...
Page 46
MARKING INFORMATION - ...