CN8330EPD CONEXANT [Conexant Systems, Inc], CN8330EPD Datasheet - Page 47
CN8330EPD
Manufacturer Part Number
CN8330EPD
Description
DS3/E3 Framer with 52 Mbps HDLC Controller
Manufacturer
CONEXANT [Conexant Systems, Inc]
Datasheet
1.CN8330EPD.pdf
(101 pages)
- Current page: 47 of 101
- Download datasheet (570Kb)
CN8330
DS3/E3 Framer with 52 Mbps HDLC Controller
2.4.4 Framing Operation
2.4.5 Alarm Detection
100441E
In DS3 mode, a parallel search framing circuit is used to recover the subframe and
M-frame alignments in the DS3 signal. Framing is initiated by an Out-of-Frame
(OOF) condition as determined by the receiver frame bit check circuitry. When 3
out of 16 consecutive subframing (F) bits are in error or when 2 out of 3
consecutive M-frames have M bit errors, an OOF condition is declared. Average
reframe time is less than 1 msec.
conducted. When three consecutive correct patterns are found, the receiver is
declared to be in frame. An OOF condition is declared when four consecutive
incorrect FAS patterns are detected. Average reframe time is less than 250 µsec.
and will continue to indicate the old framing position until the OOF condition
clears. RXMSY will indicate the new framing position when the OOF condition
is cleared.
The CN8330 receiver contains status indicators to obtain alarm information for
link maintenance.
Status Register [SR00;0x10] is updated each M-frame interval. It is set if AIS was
detected in the previous M-frame. An AIS condition is present when there is valid
framing and parity, both X-bits are equal, all C-bits are zero, and the payload bits
are 1010... starting with 10 after each overhead bit. This signal can be integrated
by the controller to declare a received AIS. In E3 mode, an unframed all-ones
signal is detected as AIS.
if the idle code condition was detected in the previous M-frame. The idle code
condition is present when there is valid framing and parity, both X-bits are equal,
all C-bits in subframe 3 are zero, and the payload bits are 1100... starting with 11
after each overhead bit. No idle code is defined for E3 signals; therefore, IdleDet
will indicate zero in E3 mode.
an active high indication that both X-bits in the previous M-frame were low. This
indication will not be set if the X-bits are in disagreement or if both X-bits are
high. In E3 mode, YelDet will be set if the A-bit is high.
consecutive zeros (prior to B3ZS/HDB3 decoding) are received. This alarm
condition is set as soon as the condition is detected. The indication is cleared
when a one's density of more than 33 percent (25 percent for E3) is achieved for
175 ± 75 clock cycles. Note that in some systems, a loss-of-signal alarm is not
cleared until the receiver is in frame. This function can be performed by the
controller.
In E3 mode, a serial search for the 10-bit FAS pattern (1111 0100 00) is
In either mode, serial data continues to be present on RXDAT and RXMSY
Alarm Indication Signal Detect [AISDet;SR00.2] in the DS3/E3 Maintenance
Idle Code Detect [IdleDet;SR00.4] is updated each M-frame interval. It is set
Yellow Alarm Detect [YelDet;SR00.3] is updated each M-frame interval and is
Loss-of-Signal Alarm [LOSAlm;SR00.0] is set as soon as 175 ± 75
Conexant
2.0 Functional Description
2.4 Receiver Operation
2-25
Related parts for CN8330EPD
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
V.34/Group 3 High Performance Fax Modem Family
Manufacturer:
CONEXANT [Conexant Systems, Inc]
Datasheet:
Part Number:
Description:
SmartV.XX Modem
Manufacturer:
CONEXANT [Conexant Systems, Inc]
Datasheet:
Part Number:
Description:
Demodulator and FEC Decoder Low-power QPSK demodulator for worldwide satellite set-top box applications
Manufacturer:
CONEXANT [Conexant Systems, Inc]
Datasheet:
Part Number:
Description:
Dual Stream QPSK/BPSK Demodulator lC
Manufacturer:
CONEXANT [Conexant Systems, Inc]
Datasheet:
Part Number:
Description:
Single-Chip FTA and FTA-CI Set-Top Box System Solution
Manufacturer:
CONEXANT [Conexant Systems, Inc]
Datasheet:
Part Number:
Description:
Dual Digital Broadcast MPEG-2 Standard Definition TV Decoder with PVR Support
Manufacturer:
CONEXANT [Conexant Systems, Inc]
Datasheet:
Part Number:
Description:
Digital Broadcast High-Definition TV Decoder with PVR Support
Manufacturer:
CONEXANT [Conexant Systems, Inc]
Datasheet:
Part Number:
Description:
MPEG-4 AVC/H.264 Video Decoder
Manufacturer:
CONEXANT [Conexant Systems, Inc]
Datasheet:
Part Number:
Description:
Dual Decode HDTV MPEG-2/H.264/VC-1 Video Decoder
Manufacturer:
CONEXANT [Conexant Systems, Inc]
Datasheet:
Part Number:
Description:
VOICE PAIR GAIN FRAMER
Manufacturer:
CONEXANT [Conexant Systems, Inc]
Datasheet:
Part Number:
Description:
Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit
Manufacturer:
CONEXANT [Conexant Systems, Inc]
Datasheet:
Part Number:
Description:
ATM Transmitter/Receiver with UTOPIA Interface
Manufacturer:
CONEXANT [Conexant Systems, Inc]
Datasheet:
Part Number:
Description:
integrated quad line interface unit unit for both 1.544 Mbps (T1) and 2.048 Mbps (E1) applications
Manufacturer:
CONEXANT [Conexant Systems, Inc]
Datasheet:
Part Number:
Description:
V.34/Group 3 High Performance Fax Modem Family
Manufacturer:
CONEXANT [Conexant Systems, Inc]
Datasheet:
Part Number:
Description:
SmartV.XX Modem
Manufacturer:
CONEXANT [Conexant Systems, Inc]
Datasheet: