S9S08SG8E2VTG Freescale Semiconductor, S9S08SG8E2VTG Datasheet - Page 57

• Manufacturer Part Number: S9S08SG8E2VTG
• Description: 8-bit Microcontrollers - MCU 9S08 UC W/ 8K 0.25UM SGF
• Manufacturer: Freescale Semiconductor

Specifications of S9S08SG8E2VTG

• Rohs: yes
• Core: S08
• Processor Series: MC9S08SG8
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 40 MHz
• Program Memory Size: 8 KB
• Data Ram Size: 8 KB
• On-chip Adc: Yes
• Operating Supply Voltage: 2.7 V to 5.5 V
• Operating Temperature Range: - 40 C to + 105 C
• Package / Case: TSSOP-16
• Mounting Style: SMD/SMT
• A/d Bit Size: 10 bit
• A/d Channels Available: 12
• Interface Type: SCI, SPI
• Maximum Operating Temperature: + 105 C
• Minimum Operating Temperature: - 40 C
• Number Of Programmable I/os: 16
• Number Of Timers: 2
• Program Memory Type: Flash
• Supply Voltage - Max: 5.5 V
• Supply Voltage - Min: 2.7 V

4.5.5
An access error occurs whenever the command execution protocol is violated.
Any of the following specific actions will cause the access error flag (FACCERR) in FSTAT to be set.
FACCERR must be cleared by writing a 1 to FACCERR in FSTAT before any command can be processed.
4.5.6
The block protection feature prevents the protected region of FLASH from program or erase changes.
Block protection is controlled through the FLASH protection register (FPROT). When enabled, block
protection begins at any 512 byte boundary below the last address of FLASH, 0xFFFF. (See
“FLASH Protection Register (FPROT and
After exit from reset, FPROT is loaded with the contents of the NVPROT location, which is in the
nonvolatile register block of the FLASH memory. FPROT cannot be changed directly from application
software so a runaway program cannot alter the block protection settings. Because NVPROT is within the
last 512 bytes of FLASH, if any amount of memory is protected, NVPROT is itself protected and cannot
be altered (intentionally or unintentionally) by the application software. FPROT can be written through
background debug commands, which allows a way to erase and reprogram a protected FLASH memory.
The block protection mechanism is illustrated in
last address of unprotected memory. This address is formed by concatenating FPS7:FPS1 with logic 1 bits
as shown. For example, to protect the last 1536 bytes of memory (addresses 0xFA00 through 0xFFFF), the
FPS bits must be set to 1111 100, which results in the value 0xF9FF as the last address of unprotected
memory. In addition to programming the FPS bits to the appropriate value, FPDIS (bit 0 of NVPROT)
Freescale Semiconductor
•
•
•
•
•
•
•
•
•
•
Writing to a FLASH address before the internal FLASH clock frequency has been set by writing
to the FCDIV register
Writing to a FLASH address while FCBEF is not set (A new command cannot be started until the
command buffer is empty.)
Writing a second time to a FLASH address before launching the previous command (There is only
one write to FLASH for every command.)
Writing a second time to FCMD before launching the previous command (There is only one write
to FCMD for every command.)
Writing to any FLASH control register other than FCMD after writing to a FLASH address
Writing any command code other than the five allowed codes (0x05, 0x20, 0x25, 0x40, or 0x41)
to FCMD
Writing any FLASH control register other than the write to FSTAT (to clear FCBEF and launch the
command) after writing the command to FCMD
The MCU enters stop mode while a program or erase command is in progress (The command is
aborted.)
Writing the byte program, burst program, or page erase command code (0x20, 0x25, or 0x40) with
a background debug command while the MCU is secured (The background debug controller can
only do blank check and mass erase commands when the MCU is secure.)
Writing 0 to FCBEF to cancel a partial command
Access Errors
FLASH Block Protection
MC9S08SG8 MCU Series Data Sheet, Rev. 7
NVPROT)”).
Figure
4-4. The FPS bits are used as the upper bits of the
Chapter 4 Memory
Section 4.7.4,
53