SC16IS762IBS-F NXP Semiconductors, SC16IS762IBS-F Datasheet - Page 24
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
SC16IS762IBS-F
Manufacturer Part Number
SC16IS762IBS-F
Description
UART Interface IC I2C/SPI-UARTBRIDGE W/IRDA AND GPIO
Manufacturer
NXP Semiconductors
Type
RS-232 or RS-485 or IrDAr
Datasheet
1.SC16IS762IBS.pdf
(60 pages)
Specifications of SC16IS762IBS-F
Product Category
UART Interface IC
Rohs
yes
Number Of Channels
2
Data Rate
5 Mbps
Supply Voltage - Max
3.6 V
Supply Voltage - Min
2.3 V
Supply Current
6 mA
Maximum Operating Temperature
+ 95 C
Minimum Operating Temperature
- 40 C
Package / Case
HVQFN-32
Mounting Style
SMD/SMT
Operating Supply Voltage
2.5 V, 3.3 V
Factory Pack Quantity
1500
Part # Aliases
SC16IS762IBS,128
NXP Semiconductors
SC16IS752_SC16IS762
Product data sheet
8.5 Interrupt Identification Register (IIR)
8.6 Line Control Register (LCR)
The IIR is a read-only 8-bit register which provides the source of the interrupt in a
prioritized manner.
Table 13.
Table 14.
[1]
This register controls the data communication format. The word length, number of stop
bits, and parity type are selected by writing the appropriate bits to the LCR.
shows the Line Control Register bit settings.
Table 15.
Bit
7:6
5:1
0
Priority
level
1
2
2
3
4
5
6
7
Bit
7
6
Modem interrupt status must be read via MSR register and GPIO interrupt status must be read via IOState
register.
Symbol
IIR[7:6]
IIR[5:1]
IIR[0]
Symbol
LCR[7]
LCR[6]
Interrupt Identification Register bits description
Interrupt source
IIR[5]
0
0
0
0
0
1
0
1
Line Control Register bits description
All information provided in this document is subject to legal disclaimers.
Table 13
IIR[4]
0
0
0
0
0
1
1
0
Dual UART with I
Description
Mirror the contents of FCR[0].
5-bit encoded interrupt. See
Interrupt status.
Description
condition to be transmitted (the TX output is forced to a logic 0 state).
This condition exists until disabled by setting LCR[6] to a logic 0.
Divisor latch enable.
Break control bit. When enabled, the Break control bit causes a break
Rev. 9 — 22 March 2012
logic 0 = an interrupt is pending
logic 1 = no interrupt is pending
logic 0 = divisor latch disabled (normal default condition)
logic 1 = divisor latch enabled
logic 0 = no TX break condition (normal default condition)
logic 1 = forces the transmitter output (TX) to a logic 0 to alert the
communication terminal to a line break condition
IIR[3]
0
1
0
0
0
0
0
0
shows Interrupt Identification Register bit settings.
IIR[2]
1
1
1
0
0
0
0
0
SC16IS752; SC16IS762
2
C-bus/SPI interface, 64-byte FIFOs, IrDA SIR
IIR[1]
1
0
0
1
0
0
0
0
Table
0
0
0
0
0
0
IIR[0]
0
0
14.
Source of the interrupt
Receive Line Status error
Receiver time-out interrupt
RHR interrupt
THR interrupt
modem interrupt
input pin change of state
received Xoff signal/special
character
CTS, RTS change of state
from active (LOW) to
inactive (HIGH)
© NXP B.V. 2012. All rights reserved.
Table 15
[1]
24 of 60
[1]