DS3172N Maxim Integrated, DS3172N Datasheet - Page 116
![no-image](/images/no-image-200.jpg)
DS3172N
Manufacturer Part Number
DS3172N
Description
Network Controller & Processor ICs Dual DS3/E3 Single Chip Transceiver
Manufacturer
Maxim Integrated
Datasheet
1.DS3171.pdf
(234 pages)
Specifications of DS3172N
Part # Aliases
90-31720-N00
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 116 of 234
- Download datasheet (2Mb)
DS3171/DS3172/DS3173/DS3174
11 OVERALL REGISTER MAP
The register addresses of the global, test, and all four ports are concatenated to cover the address range of 000 to
7FF. The address map requires 11 bits of address, ADR[10:0]. The upper address bit A[10] is decoded for the
DS3174 and DS3173 devices. The upper address bit A[10] it is not used by the DS3172 and DS3171 devices and
must be tied low at the pin.
The register banks that are not marked with an “X” are not writeable and read back all zeros. Bits that are
underlined are read-only; all other bits are read-write.
After Global Reset, all Registers will be reset to their default values.
When writing to registers with unused bits marked with “—”, always write a zero to these unused bits and
ignore the value read back from these bits.
Configuration registers can be written to and read from during a data path reset (DRST low, and RST high).
However, all changes to these registers will be ignored during the data path reset. As a result, all initiating action
requiring a “0 to 1” transition must be re-initiated after the data path reset is released.
All counters saturate at their maximum count. A counter register is updated by asserting (low to high transition) the
performance monitoring update signal (RPMU). During the counter register update process, the performance
monitoring status signal (RPMS) will be deasserted. The counter register update process consists of loading the
counter register with the current count, resetting the counter, forcing the zero count status indication low for one
clock period, and then asserting RPMS. No events shall be missed during an update procedure.
A latched bit is set when the associated event occurs, and remains set until it is cleared. Once cleared, a latched
bit will not be set again until the associated event reoccurs (goes away and comes back). A latched on change bit
is a latched bit that is set when the event occurs, and when it goes away. A latched status bit can be cleared using
clear on read or clear on write techniques, selectable by the GL.CR1.LSBCRE bit. When clear on read is selected,
the latched bits in a latched status register will be cleared after the register is read from. If the device is configured
for 16-bit mode, all 16 latched status bits will be cleared. If the device is configured for 8-bit mode, only the 8 bits
being accessed will be cleared. When clear on write is selected, the latched bits in a latched status register will be
cleared when a logic 1 is written to that bit position. For example, writing a FFFFh to a 16-bit latched status register
will clear any latched status bit, whereas writing a 0001h will only clear latched bit 0 of the latched status register.
Reserved bits and registers are implemented in a different mode. Reserved configuration bits and registers can be
written and read, however they will not effect the operation of the current mode. Reserved status bits will be zero.
Reserved latched status bits cannot be set, however, they may remain set or get set during a mode change.
Reserved interrupt enable bits can be written and read, and can cause an interrupt if the associated latched status
bit is set. Reserved counter registers and the associated counter will retain the values held before a mode change,
however, the associated counter cannot be incremented. A performance monitor update will operate normally. If
the data path reset is set during or after a mode change, the latched status bits and counter registers (with the
associated counters) will be automatically cleared. If the data path reset is not used, then the latched status bits
must be cleared via the register interface in the normal manner. And, the counter registers must be cleared by
performing two performance monitor updates. The first to clear the associated counter, and load the current count
into the counter register, and the second to clear the counter register.
116
Related parts for DS3172N
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![MAX3261CCJ](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX3263CAG](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX7528KCWP](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX8809AETL+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX1535CETJ+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
![DS2741N+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
![MAX13450EAUD+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
![MAX13451EAUD+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
![MAX17497BATE+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
QFN 16/A°/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
![MAX17502FATB+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
![MAX1978EVKIT](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products
![MAX2606EUT+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
SOT23-6/I°/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
![MAX2608EUT+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
SOT23-6/I°/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
![MAX2831EVKIT+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
EVALUATION KIT/2.4GHZ TO 2.5GHZ 802.11G/B RF TRANSCEIVER WITH INTEGRATED PA
Manufacturer:
Maxim Integrated Products
![MAX4888CETI+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
QFN/E/DUAL PCIE/SATA HIGH SPEED SWITCH WITH INTEGRATED BIAS RESISTOR
Manufacturer:
Maxim Integrated Products
Datasheet: