ST72C334J2B6 STMicroelectronics, ST72C334J2B6 Datasheet - Page 66

• Manufacturer Part Number: ST72C334J2B6
• Description: 8-bit Microcontrollers - MCU Flash 8K SPI/SCI
• Manufacturer: STMicroelectronics

Specifications of ST72C334J2B6

• Product Category: 8-bit Microcontrollers - MCU
• Core: ST7
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 8 MHz
• Program Memory Size: 8 KB
• Data Ram Size: 384 B
• On-chip Adc: Yes
• Operating Supply Voltage: 3.2 V to 5.5 V
• Package / Case: SDIP-42
• Mounting Style: Through Hole
• A/d Bit Size: 8 bit
• A/d Channels Available: 8
• Data Rom Size: 256 B
• Interface Type: SCI, SPI
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Number Of Programmable I/os: 32
• Number Of Timers: 4 bit
• Program Memory Type: Flash
• Factory Pack Quantity: 13
• Supply Voltage - Max: 5 V
• Supply Voltage - Min: 3.2 V

ST72334J/N, ST72314J/N, ST72124J
16-BIT TIMER (Cont’d)
14.3.4 Low Power Modes
14.3.5 Interrupts
Note: The 16-bit Timer interrupt events are connected to the same interrupt vector (see Interrupts chap-
ter). These events generate an interrupt if the corresponding Enable Control Bit is set and the interrupt
mask in the CC register is reset (RIM instruction).
14.3.6 Summary of Timer modes
1)
2)
3)
66/153
WAIT
HALT
Input Capture 1 event/Counter reset in PWM mode
Input Capture 2 event
Output Compare 1 event (not available in PWM mode)
Output Compare 2 event (not available in PWM mode)
Timer Overflow event
Input Capture (1 and/or 2)
Output Compare (1 and/or 2)
One Pulse mode
PWM Mode
See note 4 in
See note 5 in
See note 4 in
Mode
MODES
No effect on 16-bit Timer.
Timer interrupts cause the device to exit from WAIT mode.
16-bit Timer registers are frozen.
In HALT mode, the counter stops counting until Halt mode is exited. Counting resumes from the previous
count when the MCU is woken up by an interrupt with “exit from HALT mode” capability or from the counter
reset value when the MCU is woken up by a RESET.
If an input capture event occurs on the ICAP i pin, the input capture detection circuitry is armed. Consequent-
ly, when the MCU is woken up by an interrupt with “exit from HALT mode” capability, the ICF i bit is set, and
the counter value present when exiting from HALT mode is captured into the IC i R register.
Section 14.3.3.5 "One Pulse Mode" on page 63
Section 14.3.3.5 "One Pulse Mode" on page 63
Section 14.3.3.6 "Pulse Width Modulation Mode" on page 65
Interrupt Event
Input Capture 1
Yes
Yes
No
No
Not Recommended
Not Recommended
Input Capture 2
Description
AVAILABLE RESOURCES
Yes
Yes
1)
3)
Output Compare 1 Output Compare 2
Event
OCF1
OCF2
ICF1
ICF2
Flag
TOF
Yes
Yes
No
No
Control
Enable
OCIE
TOIE
ICIE
Bit
from
Wait
Exit
Yes
Yes
Yes
Yes
Yes
Partially
Yes
Yes
No
from
Exit
Halt
No
No
No
No
No
2)