MT9VDDT3272HG-335G2 Micron Technology Inc, MT9VDDT3272HG-335G2 Datasheet - Page 5

• Manufacturer Part Number: MT9VDDT3272HG-335G2
• Description: MODULE DDR SDRAM 256MB 200SODIMM
• Manufacturer: Micron Technology Inc

Specifications of MT9VDDT3272HG-335G2

• Memory Type: DDR SDRAM
• Memory Size: 256MB
• Speed: 167MHz
• Package / Case: 200-SODIMM
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 557-1135

Table 7:
PDF: 09005aef80804052/Source: 09005aef806e057b
DD9C16_32_64x72H.fm - Rev. E 1/08 EN
RAS#, CAS#, WE#
DQS0–DQS8
DQ0–DQ63
CK0, CK0#,
DM0–DM8
CK1, CK1#
CK2, CK2#
BA0, BA1
SA0–SA2
CB0–CB7
Symbol
A0–A12
V
CKE0
Pin Descriptions
SDA
DDSPD
V
V
S0#
SCL
V
NC
REF
DD
SS
128MB, 256MB, 512MB (x72, ECC, SR) 200-Pin DDR SDRAM SODIMM
Supply
Supply
Supply
Supply
Input
Input
Input
Input
Input
Input
Input
Input
Input
Type
I/O
I/O
I/O
I/O
–
Description
Address inputs: Provide the row address for ACTIVE commands, and the
column address and auto precharge bit (A10) for READ/WRITE commands, to
select one location out of the memory array in the respective device bank. A10
sampled during a PRECHARGE command determines whether the PRECHARGE
applies to one device bank (A10 LOW, device bank selected by BA0, BA1) or all
device banks (A10 HIGH). The address inputs also provide the op-code during a
MODE REGISTER SET command. BA0 and BA1 define which mode register
(mode register or extended mode register) is loaded during the LOAD MODE
REGISTER command. A0–A11 (128MB) and A0–A12 (256MB, 512MB).
Bank address: BA0 and BA1 define the device bank to which an ACTIVE,
READ, WRITE, or PRECHARGE command is being applied.
Clock: CK and CK# are differential clock inputs. All control, command, and
address input signals are sampled on the crossing of the positive edge of CK
and the negative edge of CK#. Output data (DQ and DQS) is referenced to the
crossings of CK and CK#.
Clock enable: CKE enables (registered HIGH) and disables (registered LOW)
the internal clock, input buffers, and output drivers.
Input data mask: DM is an input mask signal for write data. Input data is
masked when DM is sampled HIGH, along with that input data, during a write
access. DM is sampled on both edges of DQS. Although DM pins are input-only,
the DM loading is designed to match that of the DQ and DQS pins.
Command inputs: RAS#, CAS#, and WE# (along with S#) define the command
being entered.
Chip selects: S# enables (registered LOW) and disables (registered HIGH) the
command decoder.
Presence-detect address inputs: These pins are used to configure the
presence-detect device.
Serial clock for presence-detect: SCL is used to synchronize the presence-
detect data transfer to and from the module.
Check bits.
Data input/output: Data bus.
Data strobe: Output with read data. Edge-aligned with read data. Input with
write data. Center-aligned with write data. Used to capture data.
Serial presence-detect data: SDA is a bidirectional pin used to transfer
addresses and data into and out of the presence-detect portion of the module.
Power supply: +2.5V ±0.2V (-40B: +2.6V ±0.1V).
Serial EEPROM positive power supply: +2.3V to +3.6V.
SSTL_2 reference voltage (V
Ground.
No connect: These pins are not connected on the module.
5
Micron Technology, Inc., reserves the right to change products or specifications without notice.
DD
/2).
Pin Assignments and Descriptions
©2004 Micron Technology, Inc. All rights reserved