PIC24HJ64GP502-I/MM Microchip Technology, PIC24HJ64GP502-I/MM Datasheet - Page 167

• Manufacturer Part Number: PIC24HJ64GP502-I/MM
• Description: IC PIC MCU FLASH 64K 28-QFN
• Manufacturer: Microchip Technology
• Series: PIC® 24Hr

Specifications of PIC24HJ64GP502-I/MM

• Program Memory Type: FLASH
• Program Memory Size: 64KB (22K x 24)
• Package / Case: 28-QFN
• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: CAN, I²C, IrDA, LIN, PMP, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 21
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 10x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC24HJ
• Core: PIC
• Data Bus Width: 16 bit
• Data Ram Size: 8 KB
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM300027
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 10 Channel / 12 bit, 10 Channel
• Controller Family/series: PIC24
• No. Of I/o's: 21
• Ram Memory Size: 4KB
• Cpu Speed: 40MIPS
• No. Of Timers: 7
• Embedded Interface Type: CAN, I2C, SPI, UART
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164336 - MODULE SOCKET FOR PM3 28/44QFN
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

14.0
The input capture module is useful in applications
requiring frequency (period) and pulse measurement.
The PIC24HJ32GP302/304, PIC24HJ64GPX02/X04
and PIC24HJ128GPX02/X04 devices support up to
four input capture channels.
The input capture module captures the 16-bit value of
the selected Time Base register when an event occurs
at the ICx pin. The events that cause a capture event
are listed below in three categories:
FIGURE 14-1:
© 2011 Microchip Technology Inc.
Note 1: This data sheet summarizes the features
2: Some registers and associated bits
ICx pin
INPUT CAPTURE
Note: An ‘x’ in a signal, register or bit name denotes the number of the capture channel.
PIC24HJ32GP302/304, PIC24HJ64GPX02/X04 AND PIC24HJ128GPX02/X04
of
PIC24HJ64GPX02/X04
PIC24HJ128GPX02/X04
devices. It is not intended to be a compre-
hensive reference source. To comple-
ment the information in this data sheet,
refer to Section 12. “Input Capture”
(DS70198) of the “dsPIC33F/PIC24H
Family Reference Manual”, which is
available from the Microchip website
(www.microchip.com).
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization”
this data sheet for device-specific register
and bit information.
the
INPUT CAPTURE BLOCK DIAGRAM
Falling Edge Mode
(16th Rising Edge)
Rising Edge Mode
(4th Rising Edge)
PIC24HJ32GP302/304,
Prescaler Mode
Prescaler Mode
Edge Detection
Wake-up Mode
Sleep/Idle
Mode
families
and
101
100
011
010
001
of
in
ICM<2:0>
CaptureEvent
• Simple Capture Event modes:
• Capture timer value on every edge (rising and
• Prescaler Capture Event modes:
Each input capture channel can select one of two
16-bit timers (Timer2 or Timer3) for the time base.
The selected timer can use either an internal or
external clock.
Other operational features include:
• Device wake-up from capture pin during CPU
• Interrupt on input capture event
• 4-word FIFO buffer for capture values:
• Use of input capture to provide additional sources
ICTMR
- Capture timer value on every falling edge of
- Capture timer value on every rising edge of
falling)
- Capture timer value on every 4th rising edge
- Capture timer value on every 16th rising
Sleep and Idle modes
- Interrupt optionally generated after 1, 2, 3 or
of external interrupts
Note:
input at ICx pin
input at ICx pin
of input at ICx pin
edge of input at ICx pin
4 buffer locations are filled
FIFO CONTROL
TMR2 TMR3
ICxBUF
ICI<1:0>
Only IC1 and IC2 can trigger a DMA data
transfer. If DMA data transfers are
required, the FIFO buffer size must be set
to ‘1’ (ICI<1:0> = 00).
/N
FIFO
ICM<2:0>
001
111
To CPU
(In IFSx Register)
Set Flag ICxIF
DS70293E-page 167