AT91SAM9XE128-QU Atmel, AT91SAM9XE128-QU Datasheet - Page 26

• Manufacturer Part Number: AT91SAM9XE128-QU
• Description: MCU ARM9 128K FLASH 208-PQFP
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM9XE128-QU

• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 180MHz
• Connectivity: EBI/EMI, Ethernet, I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 96
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 40K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 208-MQFP, 208-PQFP
• Processor Series: AT91SAMx
• Core: ARM926EJ-S
• Data Bus Width: 32 bit
• Data Ram Size: 16 KB
• Interface Type: 2-Wire, EBI, I2S, SPI, USART
• Maximum Clock Frequency: 180 MHz
• Number Of Programmable I/os: 96
• Number Of Timers: 6
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, KSK-AT91SAM9XE-PL, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM9XE-EK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 4 Channel
• For Use With: AT91SAM9XE-EK - KIT EVAL FOR AT91SAM9XEAT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

8.1.6.2
8.2
8.2.1
8.2.2
26
External Memories
AT91SAM9XE128/256/512 Preliminary
External Bus Interface
Static Memory Controller
GPNVMBit[3] = 1, Boot on Internal Flash
The customer-programmed software must perform a complete configuration.
To speed up the boot sequence when booting at 32 kHz, the user must take the following steps:
The external memories are accessed through the External Bus Interface. Each Chip Select line
has a 256-Mbyte memory area assigned.
Refer to the memory map in
• Boot on slow clock (On-chip RC oscillator or 32,768 Hz low-power oscillator)
1. Program the PMC (main oscillator enable or bypass mode)
2. Program and start the PLL
3. Switch the main clock to the new value.
• Integrates three External Memory Controllers:
• Additional logic for NANDFlash
• Full 32-bit External Data Bus
• Up to 26-bit Address Bus (up to 64 Mbytes linear)
• Up to 8 chip selects, Configurable Assignment:
• 8-, 16- or 32-bit Data Bus
• Multiple Access Modes supported
• Multiple device adaptability
• Multiple Wait State Management
• Slow Clock mode supported
– Static Memory Controller
– SDRAM Controller
– ECC Controller
– Static Memory Controller on NCS0
– SDRAM Controller or Static Memory Controller on NCS1
– Static Memory Controller on NCS2
– Static Memory Controller on NCS3, Optional NAND Flash support
– Static Memory Controller on NCS4 - NCS5, Optional CompactFlash support
– Static Memory Controller on NCS6-NCS7
– Byte Write or Byte Select Lines
– Asynchronous read in Page Mode supported (4- up to 32-byte page size)
– Compliant with LCD Module
– Control signals programmable setup, pulse and hold time for each Memory Bank
– Programmable Wait State Generation
– External Wait Request
– Programmable Data Float Time
Figure 8-1 on page
20.
6254C–ATARM–22-Jan-10