MC908JL16CFJER Freescale Semiconductor, MC908JL16CFJER Datasheet - Page 43

• Manufacturer Part Number: MC908JL16CFJER
• Description: IC MCU 8BIT 16K FLASH 32-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908JL16CFJER

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, SCI
• Peripherals: LED, LVD, POR, PWM
• Number Of I /o: 26
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Controller Family/series: HC08
• No. Of I/o's: 26
• Ram Memory Size: 512Byte
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Digital Ic Case Style: LQFP
• Rohs Compliant: Yes
• Processor Series: HC08JL
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SCI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 26
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908JL16E, M68CBL05CE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 13 Channel
• For Use With: DEMO908JL16E - BOARD DEMO FOR MC908JL16
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: MC908JL16CFJERTR

STOP — STOP Instruction Enable Bit
COPD — COP Disable Bit
3.4 Configuration Register 2 (CONFIG2)
IRQPUD — IRQ Pin Pull-Up Disable Bit
LVIT1, LVIT0 — LVI Trip Voltage Selection Bits
IICSEL — MMIIC Pin Selection Bit
STOP_ICLKDIS — Internal Oscillator Stop Mode Disable Bit
Freescale Semiconductor
STOP enables the STOP instruction.
COPD disables the COP module. Reset clears COPD. (See
(COP).)
IRQPUD disconnects the internal pull-up on the IRQ pin.
Detail description of trip voltage selection is given in
IICSEL selects the pins to be used as MMIIC I/Os when the MMIIC module is enabled. (See
8 Multi-Master IIC Interface
Setting STOP_ICLKDIS disables the internal oscillator during stop mode. When this bit is cleared, the
internal oscillator continues to operate in stop mode. Reset clears this bit.
1 = STOP instruction enabled
0 = STOP instruction treated as illegal opcode
1 = COP module disabled
0 = COP module enabled
1 = Internal pull-up is disconnected
0 = Internal pull-up is connected between IRQ pin and V
1 = SDA on PTA2/KBI2 pin; SCL on PTA3/KBI3 pin
0 = SDA on PTD7/RxD pin; SCL on PTD6/TxD pin
1 = Internal oscillator disabled during stop mode
0 = Internal oscillator enabled during stop mode
Address: $001E
Reset:
Read:
Write:
POR:
IRQPUD
Bit 7
R
0
0
Figure 3-3. Configuration Register 2 (CONFIG2)
= Reserved
(MMIIC).)
R
6
0
0
MC68HC908JL16 Data Sheet, Rev. 1.1
R
5
0
0
U = Unaffected
LVIT1
U
4
0
Chapter 14 Low-Voltage Inhibit
LVIT0
U
3
0
DD
Chapter 13 Computer Operating Properly
R
2
0
0
Configuration Register 2 (CONFIG2)
IICSEL
1
0
0
ICLKDIS
STOP_
Bit 0
0
0
(LVI).
Chapter
43